SKE Bar 600 Zero Nicotine Prefilled Pods

Overview

The SKE Bar 600 Zero Nicotine Prefilled Pods by SKE delivers up to 600 puffs at 10mg and 20mg. Free UK delivery over £20, same-day dispatch on weekday orders before 4pm.

SKE Bar 600 Zero Nicotine Prefilled Pods: what you are buying

The SKE Bar 600 Zero Nicotine Prefilled Pods are sealed, ready-to-use e-liquid pods for people who want the flavour and the hand-to-mouth routine of vaping without any nicotine in the liquid. Each pod arrives already filled and with the mesh coil built in, so there is nothing to top up, no coil to prime from scratch and no bottle to open. You take the pod out of its packaging, seat it in the matching SKE device and start drawing. When the pod runs flat you take it out and fit a fresh one.

The headline figure is 600 puffs per pod. That is a manufacturer estimate rather than a laboratory guarantee, and later in this guide we explain how it translates into real days of use. The strength is 0mg/ml, which means the e-liquid is a blend of propylene glycol, vegetable glycerine and flavouring with no nicotine added. Because the pod is a replaceable part that clicks into a rechargeable device, rather than a complete single-use vape, it sits on the right side of the UK ban on disposable vapes that came into force on 1 June 2025.

This page is written for UK vapers and covers the practical questions people actually ask before buying: how long a pod lasts, what the flavours are like, how the battery side works, whether 0mg is the right choice for you, what to do when something goes wrong, and how the pods stack up against other ways of vaping nicotine-free. We have tried to be straight about the limits as well as the strengths. A small 600-puff pod is a convenient format, but it is not the right answer for everyone.

One point to settle early: a zero nicotine pod is for adults only. We treat every vaping product on this site as 18+, whether or not it contains nicotine, and we expect the same from anyone buying here. If you are not currently a smoker or vaper, there is no health reason to start, and these pods are not aimed at you.

Specifications at a glance

Manufacturers do not always publish a full data sheet for each pod, so the figures below separate what is stated for the product from what is typical for this pod format. Where a number is typical rather than confirmed, we say so. Check the packaging and the product images if you need an exact figure for something specific.

• Brand: SKE
• Product type: prefilled replacement pod (pod-refill format), not a complete single-use vape
• Rated puffs: approximately 600 per pod (manufacturer estimate)
• Nicotine strength: 0mg/ml, nicotine-free
• Liquid capacity: typically around 2ml per pod, which is also the largest tank or pod size the UK allows for nicotine products
• Coil: pre-installed mesh coil, usually in the 1.0 to 1.2 ohm range for mouth-to-lung inhaling
• Base liquid: propylene glycol and vegetable glycerine blend with food-grade flavouring
• Activation: draw-activated, so there is no button to press on most devices in this class
• Battery: lives in the device, not the pod; devices of this size commonly carry roughly 400 to 550mAh and recharge over USB-C
• Age restriction: 18 and over only

A quick sanity check on the numbers shows why the 600-puff claim is believable. A 2ml pod divided across 600 puffs works out at roughly 0.003ml of liquid per puff, which is in the normal range for a small mesh coil and a short, gentle draw. If you take long, hard draws you will use more liquid per puff and see fewer than 600 in practice; if you take brief sips you can see a few more. Treat 600 as a planning figure, not a promise.

Performance and puff delivery

The pod delivers its output in a fairly consistent way across its life. For the first few hundred puffs the vapour is steady, the flavour is at full strength and the draw feels smooth. Mesh coils heat quickly, so the first draw after a pause is not noticeably weaker than the one before it. Near the end of the pod, usually somewhere in the last fifth of the liquid, you will notice the flavour thinning out, the vapour getting a little warmer and perhaps a slightly papery or toasted note creeping in. That is the signal to swap the pod rather than keep pushing it.

It helps to think about the 600-puff figure in terms of days rather than puffs. A light user who takes around 100 to 150 puffs a day will get four to six days from a pod. A moderate user at 250 to 350 puffs a day will get roughly two days. Someone who chain-vapes through a commute, a work break and an evening in front of the television could finish a pod in about a day and a half. Most people sit in the middle, and a two-day pod life is a reasonable expectation.

Several things move that number up or down:

• Draw length: a three-second draw uses about twice the liquid of a one-and-a-half-second draw.
• Draw frequency: taking puffs back to back without a pause heats the coil and wick faster and burns through liquid more quickly.
• Temperature: very cold pods can feel thick and slow to wick. Let a pod that has been in a cold car warm to room temperature before use.
• Fit: a pod that is not fully seated can give weak output or none at all, which feels like a short-lived pod when it is a connection problem.

Because this is a 0mg liquid, you should also adjust your expectations on feel. Nicotine is what produces the throat hit that many vapers associate with a satisfying puff. Without it, the draw is gentler and rounder, and the sensation is closer to inhaling flavoured vapour than to anything resembling smoking. Some people find that very pleasant and easier on the throat. Others, especially recent ex-smokers, find it a little empty at first. Neither reaction is wrong; it is simply how nicotine-free liquid behaves.

Vapour production is moderate. This is a small pod with a small coil, not a high-power device, so do not expect the dense clouds of a sub-ohm tank. The format is built for discreet, low-effort use, and the output matches that.

Flavour profile and what to expect from each variant

SKE sells its 600-puff pods as individual flavour variants, and the range on offer changes with stock and with the manufacturer's own releases. Use the variant selector on this page to see what is currently available. The flavour families below are the ones that are typically found in this style of pod range, with a description of how each tends to taste so you can choose without guessing.

• Blue raspberry ice: a sweet, slightly tart blue raspberry candy flavour with a cool exhale. A common starting point for anyone new to this format.
• Strawberry ice: ripe, jammy strawberry up front, with a light menthol cooling on the way out. Sweet but not heavy.
• Watermelon ice: juicy, slightly candy-style watermelon with a clean, cool finish. One of the lighter and more refreshing profiles.
• Mango peach: a rounder, softer fruit blend with a tropical lean. No cooling agent, so it reads as warmer and sweeter.
• Pink lemonade: sharp citrus balanced by sugary sweetness, similar to a fizzy-free soft drink. Bright and easy to vape all day.
• Cherry cola: sweet cherry over a caramel-like cola base. A good option if you prefer a drink flavour to a fruit one.
• Blueberry sour raspberry: a layered berry mix with a sharp edge. Noticeably more complex than the single-fruit flavours.
• Mint or menthol: for anyone who wants a clean, cool profile without sweetness.

Zero nicotine changes how flavours present. In nicotine-containing liquids, the throat hit and a slight bitterness from the nicotine itself take the edge off sweetness. Without them, the fruit notes and sweeteners come through more clearly and can read as sweeter than the same flavour at 10mg or 20mg. If you dislike very sweet vapes, lean towards the ice or mint variants, where the cooling agent balances the sugar. If you like sweet, dessert-style flavours, the non-ice fruit blends will suit you.

Like all small pods, the flavour fades as the liquid drops. The first two-thirds of a pod usually taste as intended. In the last third you may find the flavour gets flatter. Keeping the pod upright when not in use and avoiding long gaps with the pod inserted in a hot pocket helps keep it consistent.

If you want to switch flavour, the pod format makes it simple: remove the current pod, fit the new one and give it a few minutes to saturate. There is no flushing, no cleaning and no residual mixing of flavours, because the coil is part of the pod you are removing.

Design and build quality

The pod itself is a compact plastic cartridge with a moulded mouthpiece on one end and electrical contacts on the other. A clear or translucent section lets you see the liquid level, which is more useful than it sounds: it lets you judge how much is left without counting puffs, and it lets you spot a leak or flooded chamber at a glance. The mouthpiece is oval and slim, comfortable for a relaxed grip, and the airflow channel runs straight through to the coil without any adjustable ring or sleeve.

In everyday use the build is what you would expect from this class of product. The plastic is light and reasonably firm, and the pods hold their shape when carried loose in a pocket or bag. They are not rugged. A pod dropped onto a hard floor can crack, particularly around the base seal, and a cracked pod will leak. If you carry a spare, keep it in its original packaging or in a small case rather than loose with keys and coins.

The connection between pod and device is the part that matters most for reliability. Most devices in this category use either a magnetic connection or a snug push-fit with metal contact pins, so the pod seats with a click or a firm press. Keep the contact points clean and dry. A speck of dried liquid or fluff on the contacts is behind many reports of a pod that will not fire. A quick wipe with a dry cotton bud is usually enough.

On weight and size, a pod and device combination of this type is small enough to disappear into a jeans pocket and light enough that you forget it is there. That is the main design advantage over bulkier refillable kits. The trade-off is that the pod is a proprietary shape. A SKE Bar 600 pod is designed for its matching device, so you cannot assume it will fit a different brand's hardware. Check compatibility on the product page before buying, especially if you are replacing pods for a device you already own.

The pod is also a sealed unit. You are not meant to open it, refill it or swap the coil. That keeps things simple and reduces the chance of spills, but it also means the pod cannot be repaired if something goes wrong. If it fails inside its first few days of use, treat it as a faulty item and contact us rather than trying to modify it.

Battery and charging: how the power side works

The pod has no battery of its own. The power comes from the device the pod clicks into, which means the battery question is really a question about your SKE device. Devices of this size and type commonly use a cell somewhere in the region of 400 to 550mAh, and many use USB-C charging. Check the specification printed on your device or its box for the exact figure, because we would rather you rely on that than on our estimate.

As a rough guide, a battery in that range gives enough power to work through one pod and often a little more. If you are getting through a pod every two days, you are likely to be charging the device around once or twice in that period, depending on how heavily you use it. Charging from empty to full normally takes somewhere between 30 and 60 minutes with a standard USB charger. Most devices show a light or a flashing indicator when the battery is low and may stop firing altogether once it is flat, so a dead device is almost always a charging issue and not a pod issue.

Sensible charging habits make the battery last longer and keep things safe:

• Use a reputable USB charger or a computer port. Avoid cheap, unbranded adapters, which can supply unstable current.
• Do not leave the device charging unattended for hours, and do not charge it overnight under a pillow or on a soft surface that traps heat.
• Do not charge a device that is visibly damaged, swollen or hot to the touch.
• Keep the charging port free of liquid. A bit of condensation or e-liquid in the port can stop it charging properly.
• Do not carry the device loose in a pocket with coins or keys, which can short the contacts.

Lithium batteries wear out. After a few hundred charge cycles, capacity falls and you may notice that the device needs charging more often than it used to. When that happens, stop using it and recycle it properly; do not put it in your household bin. A swollen casing, a burning smell or unusual heat are all signs to stop using the device immediately and take it to a recycling point.

Because the pod and the battery are separate, you can keep buying pods for as long as your device still holds a charge. That is a genuine cost and waste advantage over fully single-use designs, where the battery is thrown away after one liquid load.

Mesh coil technology and why it matters in a small pod

The coil is the heating element that turns liquid into vapour, and in these pods it is a mesh design. Instead of a single round wire wound around a cotton wick, a mesh coil uses a thin sheet of metal with many small perforations, laid against the wick. The practical effect is a much larger heating surface area. That gives faster ramp-up, more even heating across the wick and better flavour consistency from the first puff to the last.

For this pod, the coil is typically in the 1.0 to 1.2 ohm range, which suits a mouth-to-lung draw: you pull the vapour into your mouth first, pause, then inhale. It is the same draw style most people use with cigarettes. The airflow is moderately restricted and the resistance is tuned for the low power that a small battery can deliver safely. You do not need to adjust anything. There is no airflow ring, no wattage setting and no coil change.

Compared with an older round-wire coil, mesh has some clear advantages in a compact pod:

• Flavour: because more of the wick is heated evenly, flavours are fuller and less likely to taste burnt on early puffs.
• Efficiency: less power is wasted in heating up, so a small battery goes further.
• Wicking: a mesh coil spreads the liquid contact across its surface, which tends to reduce dry spots when you take a few draws in quick succession.

There are limits too. Mesh coils are more sensitive to being run dry than their wire counterparts, because the thin metal can overheat quickly without liquid to carry the heat away. That is why a freshly fitted pod needs a few minutes to saturate before first use, and why you should stop using a pod once it is clearly empty. Burnt coils cannot be recovered. The whole pod is the consumable, so a scorched coil means a fresh pod.

Sweet, high-VG liquids also leave residue on any coil over time. That is one reason the flavour on a 0mg sweet pod can start to taste slightly muted late in the pod's life even if there is still liquid left. With 600 puffs as the rated life, the coil is not expected to last long enough for this to become a serious problem, which is one advantage of the short-life pod design.

Nicotine strength: why 0mg, and how it fits UK rules

These pods contain no nicotine, so there is no strength to choose between. The more useful question is whether 0mg is the right level for you.

In the UK, e-liquid containing nicotine is regulated under the Tobacco and Related Products Regulations 2016. The main limits are a maximum strength of 20mg/ml, a maximum tank or pod capacity of 2ml and a maximum refill bottle size of 10ml. Those rules applied to disposable vapes before they were banned for sale on 1 June 2025, and they continue to apply to nicotine pods, refills and kits. A 0mg product falls well below the strength cap and, because it contains no nicotine, sits outside the nicotine-specific rules. We still sell it on an 18+ basis, and we ask for the same age checks as we do on nicotine products.

A practical way to think about nicotine levels:

• 20mg/ml: the UK maximum. Often used by heavier smokers moving to nicotine salts in small pod devices.
• 10 to 12mg/ml: a mid-range strength used by moderate smokers or as the first step down.
• 6mg/ml: a lower strength, common among people who have already cut back.
• 3mg/ml: a light level, usually the last stage before stopping nicotine altogether.
• 0mg/ml: nicotine-free. For flavour, habit and routine only.

If you are a current smoker, going straight from cigarettes to 0mg is a big jump, and many people who try it find the cravings are unchanged and end up smoking again. A more realistic route is to use a nicotine strength that controls cravings, then step down gradually over weeks or months until you reach zero. The NHS runs free stop smoking services in England, Wales, Scotland and Northern Ireland, and speaking to one gives you a plan with proper support. We are a shop, not a medical service, so we leave clinical advice to them.

Zero nicotine pods suit people who are already past that point: former smokers who have stepped down fully but still enjoy the ritual, people finishing a nicotine taper, and anyone who simply wants flavoured vapour without nicotine. They are also useful as a bridge product for the person who wants something in their hand during a break without reaching for nicotine.

One clear caution. Nicotine-free does not mean risk-free. You are still inhaling heated propylene glycol, glycerine and flavourings, and the long-term effects of that are not fully known. If you do not currently smoke or vape, there is no reason to start.

Who these pods suit, and who should skip them

The SKE Bar 600 Zero Nicotine pods are a narrow, specific product, and being clear about who they work for will save you money and frustration.

They are a sensible choice if you:

• have already finished a nicotine taper and want to keep the vaping routine without the nicotine.
• prefer a small, light, pocketable device over a refillable tank.
• want a simple fit-and-go pod with no refilling, priming from a bottle or coil swapping.
• like to rotate flavours and want an easy way to do so without cleaning a tank.
• are a light to moderate user who will not be annoyed by a two-day pod life.
• already own the matching SKE device and need replacements.

You should probably skip them if you:

• are currently smoking or using nicotine and have not yet stepped down. A 0mg pod will not manage cravings, and you may be better served by a low-strength nicotine pod or a conversation with a stop smoking adviser.
• are under 18. These products are not for you.
• do not already vape or smoke. There is no benefit to starting.
• are pregnant or have a health condition and are unsure about inhaling vapour. Ask your GP or pharmacist first.
• want large clouds or a big, warm throat hit. This is a low-power, mouth-to-lung format.
• get through more than a pod a day and are sensitive to running costs. A larger-capacity pod or a refillable kit will cost less per millilitre.
• do not own a compatible device and are not planning to buy one. The pod is not a standalone vape.

A final category worth mentioning: people who like to experiment with their own liquids. Prefilled pods are sealed, so you cannot swap in your own juice. If that matters to you, a refillable pod kit with a bottle of 0mg liquid gives you more control, though at the cost of a bit more mess and effort.

How to fit, use and look after a pod

The process is straightforward, but a few details prevent most of the problems people run into.

Start by checking the device is charged. If the battery is flat the pod will not fire, and you may misread that as a faulty pod. Then take the new pod out of its packaging and remove any protective cap, film or plug from the mouthpiece and base. These are there to protect the pod in transit and they will block airflow or contacts if left in place.

• Step 1: line up the pod with the opening in the device and press it in firmly until it clicks or seats flush. A loose pod is the most common cause of no vapour.
• Step 2: wait three to five minutes. This gives the cotton wick time to soak up liquid, which is important for a mesh coil. Skipping this step and taking hard draws straight away is the usual reason for a burnt first taste.
• Step 3: take two or three gentle, short puffs without inhaling fully, just to draw liquid into the wick.
• Step 4: vape as normal, using a slow, steady, two-second draw. There is nothing to press on most devices in this class; the draw triggers the output.
• Step 5: when the flavour has clearly faded, the vapour is thin or the liquid window shows the pod is nearly empty, remove it and fit a fresh one.

Storage matters more than most people realise. Keep spare pods upright, at room temperature and out of direct sunlight, where heat can thin the liquid and cause leaks. Do not leave a pod in a hot car. Do not store the device in a tight pocket where the mouthpiece can be pressed or knocked, because that squeezes liquid into the airflow channel.

If you are travelling, keep the device and pods in a small case. Check the rules of the airline or operator, as many require vape devices to travel in hand luggage and not in checked bags because of the battery.

When a pod is finished, do not put it in your household bin. Used pods contain a coil and small electronic parts and should be treated as vape waste. Many UK vape shops run take-back bins for used pods and devices, and most council household waste recycling centres have a small electricals container that accepts them. Devices with a battery should always go to a recycling point and never into general waste, where damaged lithium cells are a fire risk in collection vehicles and waste sites.

Troubleshooting common problems

Most problems with prefilled pods fall into a handful of categories, and most can be fixed in a minute or two. Work through the list below before assuming a pod is faulty.

• No vapour or the device does not fire: check the battery first. Then remove the pod, wipe the metal contacts on both pod and device with a dry cotton bud, and re-seat it firmly. Make sure any protective film on the pod base has been removed. Try a firmer draw, as some devices need a stronger pull to trigger.
• Weak flavour from a new pod: the wick has probably not saturated. Leave the pod standing upright for five minutes, then take a few short, gentle puffs before returning to normal draws.
• Burnt or harsh taste: this usually means the coil has been run dry. If the pod is more than three-quarters used, it is likely nearly empty and should be replaced. If it happened on a new pod, you probably took hard draws before it saturated. Replace the pod, wait longer next time and use shorter puffs.
• Gurgling or spitting: there is excess liquid in the airflow channel. Remove the pod, wipe the mouthpiece and gently blow through it, or tap the pod mouthpiece-down on a tissue. Keep pods upright when stored.
• Leaking from the base or mouthpiece: check for cracks, particularly if the pod has been dropped. A small amount of condensation around the mouthpiece is normal; a steady leak or liquid pooling in the device is not. Wipe the device dry before fitting a new pod and stop using the leaking one.
• Tight or blocked draw: check the mouthpiece for a stray protective cap, lint or dried liquid. A cold pod can also feel stiff to pull on; let it warm to room temperature.
• Device blinks and will not vape: this commonly indicates a low battery, a poor connection to the pod or a short-circuit protection trigger. Charge the device, clean the contacts and fit the pod again. If it persists with a second pod, the device may be at fault and not the pod.
• Pod will not seat properly: make sure it is the right pod for your device. Check that the orientation is correct and that there is no debris in the socket.

If none of this helps and the pod is clearly defective, keep the packaging, take a clear photo of the fault and contact us with your order number. We can only look into a fault properly when we can see it, and a photo saves everyone time.

Value for money and how it compares with the alternatives

Value in a pod product comes down to cost per millilitre, cost per day and how much effort the format asks of you. Prefilled pods are priced for convenience, and that convenience has a price.

Looking at it per day: if a 600-puff pod lasts you two days, the daily pod cost is half the price of one pod. A heavier user finishing a pod a day pays the full pod price every day. Buying multi-packs, where available, brings the per-pod cost down, and if you know you will use the pods steadily it is worth looking at those before buying singles.

The honest comparison is with a refillable pod kit running 0mg liquid. A refillable kit costs more upfront, but nicotine-free e-liquid in bottle form costs far less per millilitre than the same amount of liquid sealed inside a prefilled pod. Over a few months of regular use, the refillable route is almost always cheaper. What you give up is simplicity. You have to fill the pod, handle bottles, deal with the occasional spill and replace the coil every week or two. If that sounds like a chore, the prefilled approach is worth the premium. If you do not mind, refillable is better value.

Against other prefilled pod systems, a few fair observations:

• Larger-format pods: some competing pod systems sell pods rated for 1,000 puffs or more. Those cost more per pod but often less per puff, and they suit heavier users. A 600-puff pod is on the smaller side, and the smaller capacity is part of why it stays slim and light.
• Other brands' pods: brands such as IVG, Vuse and various Elf Bar-style pod ranges offer similar mouth-to-lung prefilled pods. Not every range includes a 0mg option, so availability is a real point in favour of any pod you can buy at zero nicotine in the flavour you like.
• Device lock-in: SKE pods are designed for SKE hardware. If you already own another brand's device, a pod for that device is the cheaper route than starting over.
• Single-use vapes: these are no longer legal to sell in the UK, so the realistic comparison is with other pod and refillable systems.

Where SKE Bar 600 pods make most sense is for the light-to-moderate nicotine-free vaper who wants a slim device, an uncomplicated pod swap and a range of flavours. It is a convenience product with moderate running costs, a modest puff count per pod and a short list of controls. It is not trying to be the cheapest way to vape or the one with the most power. Judge it by whether the convenience is worth the price to you, and if you find yourself burning through pods quickly, run the numbers on a refillable kit before your next order.