Smok Nfix Pod 0.8Ohm (Pack of 3)

Overview

The Smok Nfix Pod 0.8Ohm (Pack of 3) by Smok at 0mg. Free UK delivery over £20, same-day dispatch on weekday orders before 4pm.

Smok Nfix Pod 0.8Ohm (Pack of 3) overview

The Smok Nfix Pod 0.8Ohm (Pack of 3) is a set of three replacement pods for the Smok Nfix pod system. Each pod is a sealed, self-contained unit: a refillable e-liquid reservoir with a 0.8ohm coil built into the base. When the coil wears out you swap the whole pod rather than rebuilding anything by hand, which is the main reason this format suits people who want a vape that behaves the same way every day without any tinkering. With three pods in the pack, most regular users get several weeks of use before they need to reorder.

This is an accessory, not a starter kit. The pack does not include the Nfix device, a charging cable or any e-liquid, so you will need the battery unit already (or order it separately) plus a bottle of nicotine e-liquid in the strength you prefer. That is a deliberate part of the appeal for UK vapers: the pods are refillable, so you choose the flavour and the nicotine level instead of being locked into whatever a disposable happens to contain. Since single-use disposable vapes were banned in Great Britain from 1 June 2025, refillable pod systems like the Nfix have become the obvious replacement for anyone who liked the simplicity of a disposable but does not want to throw away a battery every few days.

The 0.8ohm resistance is the key detail. It places the pod in the tighter-draw, mouth-to-lung (MTL) part of the market, where you pull vapour into your mouth first, pause briefly and then inhale. That style is the closest match to the feel of a cigarette, and it is what most ex-smokers find easiest to settle into. It also means modest power use, which stretches both the battery and your e-liquid.

• Contents: three refillable Nfix pods, each with a pre-installed 0.8ohm coil
• Style: mouth-to-lung (MTL), tighter and more restricted draw
• Liquid capacity: 2ml on UK-market pods (the legal limit for nicotine tanks); some imported Nfix pods are rated at 3ml, so you may see both figures online
• Not included: the Nfix device, charging cable and e-liquid
• Age restriction: 18+ only, as with every vaping product sold in the UK

Throughout this guide we describe what to expect in realistic terms, including where the Nfix pod is a good fit and where another system may suit you better.

Compatibility and what is in the pack

Smok designs its pods around specific devices, and the Nfix pod is no exception. These pods are made for the Smok Nfix family of pod systems, and the connector, the pod shape and the airflow path are all matched to that hardware. They are not interchangeable with the pods used by Smok Novo, Smok Nord, Smok RPM or Smok Pozz, and they will not work with other brands' devices. If you are not sure which model you own, look at the base of your device or the original box before ordering, and if the name on it includes Nfix you are in the right place. If you own a variant of the Nfix line, confirm with the product listing or contact us before you buy, because manufacturers occasionally revise pod designs between versions.

Inside the pack you should find three pods, each ready to fill. The coil is already installed, so there is nothing to assemble. The pods are normally supplied sealed in protective packaging with the fill port closed, which keeps dust and moisture out during shipping. Do not expect pre-filled liquid: these are empty pods, which is what lets you choose your own e-liquid and keeps the product within the UK rules for refillable devices.

A few practical points are worth knowing before you click buy:

• You need a working Nfix device. The pods draw all of their power from it, because the pod itself has no battery or electronics.
• You need nicotine e-liquid that suits MTL. We cover the options in the nicotine section below.
• Keep a spare. Because the coil is part of the pod, a single dud coil means the whole pod is out of action. Having two others in the pack means you are never left without a working setup.
• Store them upright and dry. A pod kept in a warm pocket or car for months can dry out or leak when you first fill it.

Buying in packs of three is also the easiest way to match your replacement rhythm to your device. Most people change a pod every one to three weeks depending on how often they vape, so a single pack tends to last a month or two, and it avoids the situation where you run out on a weekend with no way to get a replacement.

Performance and puff delivery

With a 0.8ohm coil the Nfix pod is built for restrained, steady vapour rather than big clouds. At the modest power levels typical of this style of device, a draw delivers a warm, moderately dense mouthful of vapour with a noticeable throat sensation if you use a nicotine salt liquid at a sensible strength. It is not trying to imitate sub-ohm vaping, and if you are used to a big, loose draw you will find it more restrained. If you are moving from cigarettes or from a disposable, it will probably feel familiar within a day or two.

Puff count is easy to misunderstand, so here is the honest way to think about it. A pod is not rated for a fixed number of puffs the way a disposable is. Its life is set by two things: how much liquid you push through the coil, and how clean the coil stays while you do it. As a rough guide, a 2ml fill of a typical 50/50 nicotine salt liquid gives somewhere in the region of 400 to 600 puffs of normal length, with the range depending on how long you hold the fire button and how hard you pull. A pod commonly keeps tasting right for around 8 to 15ml of e-liquid, which works out at four to seven refills, so three pods can realistically cover 25 to 45ml of liquid. Treat those as estimates rather than a promise. Sweet, syrupy liquids shorten coil life, while thinner fruit or menthol liquids tend to be kinder.

Performance is also tied to how you use the device:

• Draw style: slow and steady draws of two to four seconds give smoother vapour and less coil stress than short, sharp pulls.
• Power setting: if your Nfix lets you adjust output, stay within the wattage range printed on the pod or box. A 0.8ohm MTL coil usually works comfortably in the low-to-mid teens of watts, and pushing it higher tends to burn flavour and shorten coil life without adding anything worthwhile.
• Liquid thickness: a balanced 50/50 or slightly PG-leaning liquid wicks properly through this resistance. Very thick, high-VG juice can starve the coil.
• Priming: a freshly filled pod needs a few minutes to soak the cotton. Skipping this is the most common reason for a weak or burnt first pull.

In short, expect consistent, cigarette-like delivery, not theatrics. The consistency is the selling point: once the pod is primed, the first draw and the fiftieth draw should feel alike until the coil nears the end of its life.

Flavour profile and what to fill it with

The pod itself has no flavour of its own. What it does is shape how your e-liquid tastes, and the 0.8ohm coil has a recognisable character: it produces a warm vapour rather than a hot one, which lets the middle notes of a liquid come through without the harshness that very high power can bring. Fruit, menthol, mint and tobacco liquids all show up clearly. Rich dessert and custard recipes work, but they leave residue on the coil faster, so expect to change the pod sooner if you vape them all day.

Here is how different liquid types tend to behave in a 0.8ohm MTL pod:

• Menthol and mint: clean and crisp. These are among the easiest liquids on the coil, so pods filled with them often last longest.
• Fruit and ice blends: sharp top notes carry well, and the cooling element keeps the taste lively through the pod's life.
• Tobacco: the warm vapour suits tobacco profiles well, and many people who are leaving cigarettes start here. Lighter, more natural tobacco liquids tend to read better than very sweet ones.
• Sweet bakery and custard: tasty at first, but sugars caramelise on the coil and can dull flavour after a week or so. If you love these, keep a spare pod ready.

To keep flavour consistent, use the same liquid type for the whole life of a pod. Switching from a dark tobacco to a fresh mint in the same pod usually leaves a muddy mix of tastes because the cotton holds on to what it has absorbed. If you want to change flavour, switch to a new pod, which is another reason the pack of three is handy: you can assign one pod per flavour family, such as one for menthol, one for fruit and one for tobacco, and rotate between them without cross-contamination.

If a pod starts tasting flat, the cause is almost always the coil rather than the liquid. Flat or slightly burnt flavour that does not improve after a rinse and a fresh fill is the signal that the coil has reached the end of its useful life. We cover troubleshooting later in this guide, but in practice the flavour tells you when to move on to the next pod in the pack.

Design and build quality

Smok has been making pod systems for years, and the Nfix pod follows the familiar approach: a clear or translucent reservoir that lets you see the liquid level at a glance, a moulded body that locks into the device, and a mouthpiece shaped to sit comfortably on the lips. The plastics are a rigid material that should stand up to normal handling, and the pod seats into the device with a firm connection rather than a loose wobble. A well-seated pod matters more than it sounds, because a poor seat can cause intermittent firing, leaks around the base or an error message on the device.

The construction is simple by design. The coil head is built into the base of the pod, so there are no screw threads to cross-thread and no separate coil to buy. The reservoir is sealed with a fill-port plug, normally silicone, and the airflow channel runs through the base to the coil. The result is a unit that is hard to assemble incorrectly, which suits first-time vapers and anyone who would rather not experiment.

A few things to look at when the pack arrives:

• Clean seals. The fill-port plug should sit flush with no visible gaps.
• No cracks or stress marks in the reservoir, especially around the join to the base.
• Clear airflow. The air hole at the base should be open and free of debris.
• Intact packaging. The pods should arrive protected, with no signs of prior use.

If any of those points fail on arrival, contact us with your order number and a photo so we can sort it out. Because the pod is a consumable component, build quality is judged less on how long the plastic lasts and more on whether the seal, the coil and the connection behave properly for the life of each pod. In that respect, the Nfix is a conventional, uncomplicated design with no surprises, which is useful. Treat the pods gently, keep them out of direct sun or a hot car, and avoid dropping them onto hard floors; the reservoir will take everyday knocks but is not built to survive being crushed in a bag with keys and coins.

Battery and charging considerations

The pods in this pack do not contain a battery, so everything in this section relates to the Nfix device they plug into. The Nfix kit uses a built-in rechargeable battery in the 700mAh class, with a power output that reaches up to around 25W, and it charges over a USB cable. A 700mAh cell is modest, but a 0.8ohm MTL pod does not demand much power, so for many people a charge lasts most of a day. Heavy users, or anyone who chain-vapes, may want to top the device up at lunchtime.

The pod and the battery interact in a few ways that are worth understanding:

• Higher resistance, longer battery life. Because a 0.8ohm coil draws less current than a sub-ohm coil, the battery is stretched further than it would be on a low-resistance pod.
• Wattage matters. If you can adjust power, every extra watt costs battery life, and above a certain point it also reduces coil life. Stay within the pod's recommended range.
• A flat battery is not always a pod fault. If the device stops firing or flashes, check the charge first before assuming the new pod is faulty.
• Contacts need to be clean. E-liquid residue on the connection point can cause intermittent firing. Wipe it with a dry, lint-free cloth or cotton bud.

For safe charging, use a good-quality cable and a standard USB wall adapter or computer port from a reputable maker. Do not leave the device charging unattended overnight on a soft surface such as a bed or sofa, and unplug it once the indicator shows it is full. If the device gets noticeably hot during charging, or the battery swells, stop using it and take it to a proper recycling point; never keep using a damaged lithium-ion cell.

One practical tip is to remove the pod before storing the device for long periods. Leaving a filled pod seated for weeks can cause liquid to seep towards the connection and make it harder to get a clean contact. When you are travelling, keep the device and pods upright in a pocket or case, ideally with the pod removed, which also prevents accidental firing in a bag.

Coil technology and resistance explained

The coil is the part of the pod that does the work, so it is worth a clear explanation. Inside the base is a small heating element wrapped or bonded with organic cotton wicking. When you draw on the mouthpiece the device fires, current flows through the element, the element heats up, and the cotton delivers a small amount of e-liquid that is vaporised into the airstream. The resistance of the element, measured in ohms, determines how much current it draws at a given power and how the vapour feels.

A resistance of 0.8ohm is a middle-of-the-road figure for pod vaping. It is lower than the 1.0ohm to 1.4ohm coils that suit very tight, cigarette-style draws and higher than the 0.3ohm to 0.6ohm coils that suit looser, direct-to-lung vaping. In practice the 0.8ohm pod is a good choice for people who want a bit more vapour and flavour than a very restricted coil provides, without moving into territory that needs a bigger battery and more liquid.

Smok has used different coil constructions across its pod ranges, including dual-coil and mesh designs, and each has strengths. Mesh coils spread the heating over a wider surface and typically give faster ramp-up and broader flavour, while conventional wire coils are simple, forgiving and usually kinder on cheaper liquids. For the exact build of this pod, check the product listing or the packaging, because the details can change between revisions. What stays constant is the principle: the more evenly a coil heats, and the better it is wicked, the longer it tastes good.

• Wicking: the cotton must stay saturated. If it dries out, the coil burns, and a burnt coil cannot be repaired.
• Liquid choice: thicker, sweeter liquids gum up the cotton more quickly. Thinner, 50/50 liquids keep it moving.
• Power: consistently pushing a coil above its range overheats the wick and shortens life.
• Chain vaping: short gaps between draws do not give the cotton time to re-saturate, which causes dry hits. Pause for a few seconds between draws when you can.

Because the coil is not replaceable on its own, the pod's working life is simply the coil's working life. Looking after it, by priming, by not overfilling and by not chain-vaping, is the single most effective way to get more out of each pod in the pack.

Choosing nicotine strength

Because these are refillable pods, nicotine strength is decided by the e-liquid you pour in, not by the pod. In the UK, nicotine e-liquid is limited to 20mg/ml (2%), sold in bottles of no more than 10ml, and that same 20mg ceiling applied to the disposable vapes that were sold before the ban. Nicotine salt liquids are the usual choice for MTL pods because they deliver nicotine smoothly at higher strengths without the throat harshness that freebase nicotine would cause at the same level.

As a starting point, think in terms of your current habit:

• Heavy smokers (around 15 or more cigarettes a day): 18mg to 20mg nicotine salt is where most people begin. It gives enough nicotine to take the edge off cravings without needing to vape constantly.
• Moderate smokers (around 8 to 14 a day) or heavy disposable users: 10mg to 12mg nicotine salt is usually sufficient and noticeably gentler on the throat.
• Light smokers or social smokers: 5mg to 6mg nicotine salt, or 3mg to 6mg of freebase nicotine in a 50/50 liquid, is often enough.
• Former smokers who want to stay off cigarettes with minimal nicotine: 3mg nicotine, or a zero-nicotine liquid, is a realistic goal and lets you step down gradually.

These are guidelines, not prescriptions. Most vapers find that after the first week they naturally settle on a strength that keeps them comfortable, and many drift down over time. If you find yourself chain-vaping, feeling unsatisfied or going back to cigarettes, the strength is probably too low, and a step up is reasonable. If you feel dizzy, nauseous, have a racing heart or a very harsh throat hit, the strength is too high and you should step down.

The 0.8ohm resistance is not tuned for very high-strength freebase nicotine, because that tends to feel harsh at pod-vape power levels, so if you prefer freebase keep it to the lower strengths. If you are non-smoking, you should not start vaping nicotine at all, and anyone who is pregnant, has a heart condition or is on medication should speak to a doctor or pharmacist first. Free local stop-smoking services in the UK can also help you choose a strength and plan to reduce it over time.

Who the Nfix 0.8ohm pod is for

This pod suits a specific group of vapers, and it helps to be clear about who that is so you can judge whether it fits your needs.

It is a good fit if you:

• Already own a Smok Nfix device and need replacement pods, which is the simplest reason to buy.
• Are moving from cigarettes and prefer the tighter, mouth-to-lung style that feels closer to smoking.
• Are moving from disposables after the 2025 ban and want something refillable with a similar level of simplicity.
• Want low maintenance, with no coil building, no screw threads and no tools involved.
• Like to keep a few spares in a drawer so a failed coil never leaves you without a working device.
• Want a modest, lower-power setup that stretches a small battery across a day.

It is probably not the right choice if you:

• Do not own an Nfix device, because the pods will not work in any other hardware.
• Prefer big, loose, direct-to-lung clouds, in which case a lower-resistance pod on a bigger device suits you better.
• Vape very thick, high-VG liquids, which can struggle to wick through a 0.8ohm coil.
• Want a fully rebuildable setup with your own coils and cotton, since this is a sealed pod design.
• Do not currently smoke or vape, because nicotine is addictive and these products are for adult smokers looking for an alternative.

There is a middle group worth a mention: people who like the Nfix hardware but find the tightest coils too restrictive. For them the 0.8ohm pod is a natural step, because it opens up the draw a little without leaving the MTL family. If you are unsure, the fact that a pack contains three pods gives you room to experiment with different liquids and power settings without committing to a large spend on a single pod. And if you try it and find the style is not for you, our support team can suggest other pod systems that may match your preferences better.

How to fill, prime and use your pod

Getting the first fill right makes the difference between a pod that lasts weeks and one that burns out in days. Follow the sequence below each time you start a fresh pod.

• Step 1: Check the pod. Remove it from its packaging and confirm that the base is clean, the airflow hole is open and the fill port plug is seated.
• Step 2: Open the fill port. Pull back or lift the silicone plug as shown on the pod. Keep the pod upright and avoid touching the inside of the port.
• Step 3: Fill slowly. Tilt the bottle nozzle against the side of the port and let the liquid run down the wall of the reservoir instead of dropping straight in. Stop just below the maximum line. Overfilling pushes liquid into the airflow and is the usual cause of leaks.
• Step 4: Close the port. Press the plug fully home so it seals flush.
• Step 5: Let it soak. Wait five to ten minutes before the first draw so the cotton can absorb the liquid. This is the step most people skip, and it is the most common reason for a burnt first pull.
• Step 6: Seat the pod. Push it into the device until it clicks into place. If your Nfix has adjustable output, begin at the low end of the recommended range.
• Step 7: Take a few gentle draws. Draw without firing for the first one or two pulls if your device allows it, or take short draws to pull liquid to the coil before settling into normal use.

For everyday use, inhale slowly in the mouth-to-lung style: draw vapour into the mouth over two to three seconds, hold it for a moment, then breathe it into the lungs and exhale. Do not hold the fire button without drawing, and do not fire the device dry. Top up when the liquid falls to roughly a third of the pod, rather than waiting until it is empty, because running a pod nearly dry is what starts coil damage. Change liquid only when you swap pods if you want clean flavour, and store the device upright when not in use.

If you are switching to a new pod, you can recycle the old one with other small electricals. Remove any remaining liquid first by drawing it out or soaking up the last drops with a tissue, then put the empty pod in your household waste electrical collection or take it to a drop-off point.

Troubleshooting common problems

Most problems with pod systems have simple causes, and a bit of methodical checking usually solves them without needing a replacement. Work through the situations below before assuming a pod is faulty.

• Burnt taste on the first draw. The cotton was not saturated. Wait a few more minutes, take a few gentle draws without pressing the button for long, and keep the power at the low end. If the taste persists after a fresh fill and a proper soak, the coil may have been damaged and the pod should be replaced from the pack.
• Weak or flat flavour. The coil is gummed up or nearly at the end of its life. Try emptying the pod, rinsing it with lukewarm water, drying it completely and refilling. If flavour does not recover, swap in a fresh pod.
• Leaking. Causes include overfilling, a plug that is not fully seated, a cracked reservoir, or a pod left lying on its side. Wipe it clean, check the seal, refill to a lower level and keep it upright. Persistent leaking from a new pod is worth reporting to us.
• Gurgling or spitting. Excess condensation in the airflow. Blow gently back through the mouthpiece with the pod removed, or wipe the mouthpiece and airflow area dry.
• Device does not fire or flashes. Check the battery charge, then make sure the pod is seated fully and the contacts are clean. Remove the pod, wipe both sets of contacts and reseat.
• Dry hits. The coil is not getting liquid quickly enough. Refill the pod, give it time to soak, use a thinner liquid if you have been using a very thick one, and space out your draws.
• Throat hit feels harsh. The nicotine strength may be too high for the style, or the power too high. Drop one setting or move to a lower-strength liquid.

If you work through these steps and a brand new pod from the pack still behaves badly, keep the packaging and contact us. Sometimes a single pod in a batch has a faulty coil or a poor seal, and the fact you have three means the other two are likely to work correctly while we sort out the faulty one. Please do not try to disassemble the pod or pierce the reservoir, because there is nothing inside you can repair, and it risks liquid contact with skin.

Value for money, comparisons and recycling

Judging value on a consumable like a vape pod means looking at cost per week of use, not the sticker price. A pack of three pods, at the price shown on the listing, divides into a cost per pod that is normally lower than buying singles. If you replace a pod every one to three weeks, a single pack lasts about a month or two, and the running cost of coils plus e-liquid usually works out well below the cost of a regular cigarette habit and often below the cost of buying a stream of disposables. Liquid is a separate expense, and a 10ml bottle of nicotine salt liquid lasts a moderate vaper a good while at MTL power levels.

It is fair to compare the Nfix pod with the alternatives, because the pod is only worth buying if the platform suits you:

• Smok Novo pods: a widely stocked range that is generally more current than the Nfix, with a large choice of pod resistances and good availability. If you do not already own an Nfix and want a newer device, Novo hardware is worth looking at first.
• Vaporesso XROS pods: another popular family with a 0.8ohm option and a similarly easy-to-use design. Taste and draw are comparable, and the deciding factor is usually which device you like holding.
• Voopoo and Geekvape pods: credible alternatives with their own pod ecosystems. They are not cross-compatible, so the choice is about the whole device rather than just the pod.
• Disposables: now off the legal market in Great Britain, and by design a worse deal for the environment and, over time, for your wallet.

The honest summary is that the Nfix is an established, older platform. If you already own the device, buying these pods is the simplest and cheapest way to keep using it. If you are starting from scratch you may find newer systems offer more features, so compare options before you commit. The pods themselves are a straightforward product: they do what they should, they are simple to use and the 0.8ohm resistance covers a lot of vapers' needs.

On the environmental side, treat used pods and old devices as electrical waste. Empty pods contain a small metal coil, and the device contains a lithium-ion battery that must never go in your normal bin or recycling box. Many UK retailers now offer a take-back service for vaping products, and household waste recycling centres and electrical drop-off points accept them too. Remove any leftover liquid, keep pods and devices out of the general waste, and use a drop-off point so the materials can be recovered safely.