GeekVape H45 Hero 2 Pod Vape Kit Black Orange

Overview

The GeekVape H45 Hero 2 Pod Vape Kit Black Orange by Geekvape in Black Orange at 0mg. Free UK delivery over £20, same-day dispatch on weekday orders before 4pm.

GeekVape H45 Hero 2 Pod Kit: Overview

The GeekVape H45 Hero 2 Pod Vape Kit is a refillable pod system from Geekvape, the Shenzhen manufacturer best known for the rugged Aegis range of devices. The H45 name points to the 45W maximum output, and the Hero 2 label marks it as the second generation of the Aegis Hero line. Most pod kits sit in the 15W to 25W bracket and are tuned for tight, cigarette-style draws. This one is aimed at vapers who want a looser draw, more vapour and a bit more power on tap, without stepping up to a full sub-ohm mod, a separate battery and a tank.

It is a proper kit, not a single-use product. You get a rechargeable device, a refillable pod with a replaceable mesh coil, and a USB-C cable, and you supply your own nicotine salt or freebase e-liquid in a 10ml bottle. That matters for UK buyers. Single-use disposable vapes can no longer be sold in the UK, so a refillable kit like this is the practical route for anyone who liked the convenience of a pocket device but wants to choose their own flavours and keep running costs down. When the coil wears out you swap it for a new one rather than throwing the whole device away.

The H45 Hero 2 sits in an interesting spot in the Geekvape catalogue. It is more powerful than the small starter pods that people buy for a first week of vaping, but it is far easier to live with than a 80W mod. The adjustable output means you can run it gently at 20W to 25W for a mouth-to-lung (MTL) style draw, or push it towards 35W to 45W with the lower-resistance coil for a restricted direct-to-lung (RDL) feel with a warmer, denser vapour. That flexibility is the main reason experienced vapers keep one in a coat pocket as a backup device, while newer vapers use it as a first proper step beyond a basic starter pen.

This guide covers what the kit does well, where it falls short, and how it compares with other pod systems you are likely to be cross-shopping. We give the specifications we can stand behind, practical guidance on coils and nicotine strength, and a troubleshooting section for the problems that actually come up. The kit is for adult smokers and existing vapers only. If you do not smoke or vape already, this product is not for you.

One note on variants: the kit is sold in a range of nine colourways, and the colour you choose changes the look of the device only. The electronics, the pod and the coil options are the same across the range. If you are unsure which finish to pick, the later section on design and build quality describes how the finishes behave in daily use.

Key Specifications at a Glance

Specifications are the quickest way to judge whether a pod kit fits what you want, so here are the headline figures. Where a number depends on the market the kit is sold into, we say so. Always check the packaging on your own unit, because manufacturers revise components between batches.

• Device type: refillable pod kit with adjustable output and a replaceable mesh coil.
• Battery: built-in 1400mAh lithium-ion cell, charged over USB-C.
• Output range: variable power up to a maximum of 45W.
• Pod capacity: the international version of the pod holds 4ml. UK rules cap refillable tanks and pods at 2ml, so UK-market kits ship with a 2ml pod.
• Coil type: mesh coil in a replaceable base, supplied in a lower-resistance and a higher-resistance option depending on the kit contents. Check the number printed on the coil base.
• Durability: built to the Aegis design brief, with a dust, water and shock resistance rating on the Aegis family. Treat it as splash and drop tolerant, not as a device to leave underwater.
• Charging port: USB-C with pass-through behaviour, so you can vape while the cable is plugged in if you must.
• Activation: button fire, with a protection system that cuts power on short circuit, over-time firing and low voltage.
• E-liquid compatibility: works with both nicotine salt and freebase nicotine in 50/50 and 70/30 VG/PG blends, with the best results coming from 50/50 and 60/40 blends.
• Nicotine limit in the UK: e-liquid sold for refilling is capped at 20mg/ml, and bottles are limited to 10ml.

A couple of these figures deserve context. A 1400mAh battery is a mid-size cell for a pod device. It is larger than the 800mAh to 1000mAh cells found in the slimmest pod kits, and smaller than the 2000mAh to 3000mAh cells in chunky mod-style kits. The result is a device that is slightly thicker than a pen-style pod but still sits comfortably in a jeans pocket.

The 45W ceiling is more than most users will ever need in daily use. Think of it as headroom: running a coil comfortably within its range, rather than flat out, is what keeps flavour clean and coils lasting longer. If you find yourself living at maximum power with the lower-resistance coil, a larger device would suit you better.

Performance and Vapour Delivery

The main thing the H45 Hero 2 offers over a standard small pod is how it behaves under load. A basic 15W pod device has one setting, one draw style and a fixed amount of vapour. The Hero 2 lets you adjust the output, and the mesh coil gives a wide heating surface that ramps quickly and holds a steady temperature through a long pull.

At the low end, around 18W to 25W, the kit behaves like a good MTL pod. The draw is on the tighter side, the throat hit from nicotine salts is clear but controlled, and the flavour sits close and concentrated. This is the range to start at if you are coming off cigarettes, because the draw and hit feel familiar. Vapour production at this setting is modest, and the pod will last a long time.

In the middle of the range, around 28W to 35W, the device opens up. The vapour gets warmer and fuller, flavour sharpens on fruit and dessert profiles, and the draw feels looser without turning into a cloud-chasing setup. Most users will find their personal sweet spot here. Using a 50/50 e-liquid at around 30W gives a balanced result: enough throat hit to feel satisfying, enough vapour to taste the flavour, and sensible e-liquid consumption.

Up towards 40W to 45W, the kit delivers the densest vapour it can manage. This only makes sense with the lower-resistance coil and a higher VG liquid. Expect noticeably faster e-liquid use, faster battery drain and a warmer vapour. A 2ml pod will empty quickly at these settings, which is the trade-off of the UK pod size cap. If you regularly vape at the top of the range, plan to refill more often than you would with the 4ml international pod.

Puff count is a figure that retailers love to quote, but it depends heavily on settings. As a rough guide, a 2ml fill at moderate power gives somewhere in the region of 400 to 600 puffs before the pod is empty, depending on the strength of your draw and the wattage. At lower wattage it stretches further, and at high wattage it falls short of that. We would rather give you a realistic range than a headline number lifted from a spec sheet, because a figure that ignores wattage and draw length is not much use in practice.

Response time is quick. The mesh coil starts producing vapour almost as soon as you press the button, with no noticeable lag, and the chipset keeps output consistent as the battery drains from full to the low-voltage cut-off. That consistency is easy to overlook, but it separates a well-tuned kit from a cheap one: the last third of the battery should taste and feel much like the first.

Flavour Delivery and E-Liquid Styles That Suit the Kit

A pod kit has no flavour of its own. What you taste is down to the e-liquid you choose, the coil, and the power you run. That said, some devices are noticeably better at carrying certain flavour families, and the H45 Hero 2 has a clear character worth describing.

The mesh coil is the main reason. Mesh heats a large, evenly distributed area of wick, which means the liquid vaporises at a more uniform temperature than it would on a simple round-wire coil. In practice, that gives you cleaner top notes, less of the burnt edge that appears when part of a coil runs hot, and better consistency from first puff to last. Fruit, menthol and dessert profiles all benefit.

Here are eight flavour styles that suit this kit, with notes on how to run them.

• Blue raspberry: a sweet-tart profile that holds up well at 25W to 32W. Tangy top notes come through clearly on a mesh coil.
• Strawberry ice: a common choice for a reason. The cooling agent stays smooth at moderate power, but at the top of the range it can feel sharp, so dial back if it tickles your throat.
• Mango: thick fruit flavours need a little more power to bring out the sweetness. Try 30W to 35W with a 50/50 blend.
• Menthol: a straight menthol or peppermint liquid is a good fit for smokers moving over from menthol cigarettes. Lower wattage keeps the cooling clean.
• Classic tobacco: tobacco blends can taste flat on very low power and harsh on very high power. The middle of the range suits them best.
• Vanilla custard: creamy dessert liquids are thicker, so they can gum up a coil faster. Use a 50/50 blend and expect to replace the coil slightly sooner.
• Cola: a sweet, slightly spiced profile that does well at 25W to 30W and gives a recognisable, fizzy-sweet finish.
• Mint: spearmint or polo-style mint is a good alternative if menthol is too icy. It stays crisp on the mesh coil.

A practical tip: when you change flavour, rinse the pod and fit a fresh coil if you can. Dark tobaccos and heavy desserts leave residue that can ghost into a light fruit liquid. If you vape several flavours, keep a spare pod for each family.

Do not expect a single setting to suit every liquid. Menthol and mint generally prefer less power, tobacco and dessert profiles prefer a bit more, and fruit sits in between. Spend a day finding the wattage at which your chosen flavour tastes the way you want, then leave it there.

Design, Build Quality and Colour Range

Geekvape built its reputation on tough, practical hardware, and the Hero 2 follows that line. The body is a chunky, rounded rectangle with a slightly textured finish, and it feels dense in the hand. It is not the slimmest pod on the market, and it is not trying to be. The extra thickness goes to the 1400mAh cell and the protective construction.

The shell is designed to take everyday knocks. The Aegis family carries a dust, water and shock resistance rating, which in plain terms means rain, a splash from a tap or a drop from pocket height should not end the device. We would still treat that rating as insurance, not an invitation: do not submerge it, do not leave the USB-C port wet while charging, and dry the port off before plugging in.

The pod clicks into the body with a firm magnetic or friction fit, depending on how the pod is seated, and does not rattle when seated properly. Pull the pod out and check the contacts occasionally. A bit of e-liquid residue on the contacts is the most common reason for a kit to give an error message or intermittent firing, and a dry cotton bud sorts it in seconds.

The button has a clear, positive click, and the display gives you the information you need: power setting, battery level and a warning when something is wrong. Nothing about the interface is complicated. The device has a locking function to stop accidental firing in a bag or pocket, and it is worth learning that shortcut from the manual before you carry the kit around.

The kit is sold in nine colourways, from darker finishes to brighter options. The darker shades hide fingerprints and e-liquid smudges better, while lighter and metallic finishes show wear on the corners over time. All of them share the same internals, so the choice is purely a matter of taste. If you tend to carry your device loose in a pocket with keys, go for a darker option, because scuffs show less.

One thing to be aware of is weight. The kit is heavier than a slim pen pod, and some people notice it in a light summer shirt pocket. If you want something that disappears in your hand, a smaller device will suit you better. If you want something that feels solid and survives a commute, the Hero 2 is a reasonable pick.

The pod itself is clear enough to see the liquid level at a glance, which helps you avoid dry hits. Look at the level before you press the button, not after you notice a burnt taste.

Battery Life and USB-C Charging

The 1400mAh battery is the middle ground between convenience and run time. How long it lasts depends almost entirely on the wattage you choose. As a rough guide:

• Around 20W to 25W (MTL style): a full charge usually lasts a full day of moderate vaping, and heavy users will want a top-up in the evening.
• Around 30W to 35W: expect roughly half to three-quarters of a day for a typical user, since power draw rises quickly with wattage.
• Around 40W to 45W: the battery drains fast. Plan on recharging within a few hours of regular use.

These are indicative figures, not lab-tested guarantees. Your puff length, your pause between puffs and the temperature you vape in all change the result. Cold weather lowers battery output, and a device kept in a cold coat pocket will report a lower charge than it would indoors.

Charging runs through a USB-C port. Use a decent quality cable and a standard phone-type charger from a reputable maker, and avoid very cheap unbranded adaptors. A full charge from empty typically takes around an hour to an hour and a half with a 5V charger rated at 1A to 2A. The device does not need a fast-charge brick, and a high-wattage charger will not make it charge faster than its limit.

A few habits extend battery life:

• Do not run the battery flat every time. Lithium cells last longer if you top them up before they reach zero.
• Do not leave the kit on charge for days. Unplug it once the indicator shows it is full.
• Never charge a damaged device or one with a swollen case. If the body looks bulged, stop using it.
• Do not leave the device in a hot car or in direct sunlight.
• Keep the USB-C port dry and free from pocket lint.

Vaping while charging, known as pass-through, is possible but not ideal. It generates heat in the cell and is hard on the battery over time. Use it for an emergency, not as a habit.

When the kit finally reaches the end of its life, do not put it in household rubbish or a normal recycling bin. It contains a lithium-ion battery, and in the UK electronic waste should be taken to a proper drop-off point. Many local recycling centres accept vapes and small electricals, and retailers that sell vaping products are required to take back waste equipment of the same type. Look for the crossed-out wheelie bin symbol on the packaging, and ask in store or contact the retailer if you are unsure where to go. Used pods and coils are best returned in the same way where a scheme exists.

Mesh Coil and Pod Technology

The coil is the part that decides how a pod kit tastes and feels, so it is worth understanding. The H45 Hero 2 uses a mesh coil design: instead of a single thin wire wrapped around a cotton wick, a flat strip of fine mesh runs along the wick, giving a much bigger heating surface. That wider surface means the e-liquid is heated more evenly and more quickly.

There are practical advantages to this. Mesh coils usually give a faster ramp-up, a smoother vapour, and a more even flavour from puff to puff. They also tend to last a decent time, since the heat is spread across more material and no single spot gets overworked. The trade-off is that mesh coils are more sensitive to liquid choice. Very sweet, very thick liquids can build up on the mesh and shorten its life.

The kit is supplied with coil options of different resistance. The general rule:

• Lower resistance (around 0.4 ohm): a looser draw, more vapour, and a warmer hit. Suits higher wattage and lower nicotine strengths, and works well with 50/50 or 60/40 liquids.
• Higher resistance (around 0.6 ohm): a tighter draw, a more cigarette-like feel, and longer pod life. Suits lower wattage and higher nicotine salt strengths.

Check the figure printed on the coil base before you fit it, and match your wattage to the range printed on the coil. Running a coil outside its recommended range is the quickest way to ruin it.

Priming matters. A new coil must be soaked before the first puff. Fill the pod, then wait for 5 to 10 minutes so the cotton can absorb the liquid, and take a couple of short, gentle puffs without pressing the button for the first few seconds, so the wick wicks properly. Skipping this step is the cause of most early dry hits and burnt tastes.

Coil life depends on use. A typical coil gives one to two weeks of regular vaping, longer if you vape lightly and use thinner liquids, shorter if you run high power with sweet dessert liquids. Signs it is ending: a muted or burnt flavour, gurgling, reduced vapour, or a bitter edge that does not go away after a fresh fill. Replace the coil rather than trying to nurse it along.

The pod is a refillable design with a fill port that opens for filling and closes firmly afterwards. The pod seals against the coil with a silicone gasket. If you ever see leaking, check that gasket first, then confirm the coil is pushed in fully. The pod is a consumable item. With care it will last through several coils, but eventually the plastic clouds and the seals soften, and a replacement is cheap compared with the kit.

Choosing the Right Nicotine Strength

Nicotine strength is the single biggest factor in whether a new kit feels right. Get it wrong and a good device feels harsh or unsatisfying. The rules in the UK set the framework: refill e-liquid for vaping is capped at 20mg/ml, and bottles are limited to 10ml. That 20mg figure is the legal maximum, not a recommendation. Most people do not need to use it, and the H45 Hero 2 in particular rarely suits it.

The reason is simple: this kit makes more vapour than a basic pod, so you inhale more nicotine per puff. A strength that feels fine on a 12W starter pen can be harsh and heavy at 30W. Here is a practical guide.

• Nicotine salts, 10mg/ml: a good starting point at 28W to 40W with the lower-resistance coil. Smooth throat hit, solid nicotine delivery, and easy to vape for long periods.
• Nicotine salts, 20mg/ml: best saved for 18W to 25W with the higher-resistance coil, for people leaving a heavy smoking habit. At higher wattage it is usually too strong and can cause headaches or nausea.
• Freebase nicotine, 3mg to 6mg/ml: suits a looser draw at higher wattage. This is the traditional approach for direct-to-lung vaping, and it gives a gentle throat hit.
• Low strength or zero nicotine: for people who have stepped down and want a lighter vape. The kit works equally well with low-nic liquid.

If you smoke more than 15 cigarettes a day, start at 20mg salt in the 20W to 24W range with the higher-resistance coil, and move down in strength over weeks as your cravings settle. If you smoke fewer than 10 a day, 10mg to 12mg salt is a sensible start. People who have vaped for years on freebase often prefer 6mg freebase at 30W or more.

Signs the strength is too high: coughing, dizziness, a sick feeling, or a racing heartbeat. Signs it is too low: constant cravings, vaping much more often than you want to, or going back to cigarettes. Adjust in small steps, and give each change a couple of days.

Two more cautions. First, never mix nicotine at home without proper knowledge and measuring tools. Buy ready-made liquids in the strength you need. Second, keep all e-liquid and the device away from children and pets. Nicotine is toxic if swallowed, and a pod full of liquid is a risk in a house with small children. Store bottles upright, closed, and out of sight.

If you want to reduce your nicotine over time, the kit helps: you can drop the strength in steps, or lower the wattage. Many users report that a gradual step-down works better than quitting abruptly. Speak to a pharmacist or your local stop smoking service if you want support.

Who the H45 Hero 2 Suits, and Who Should Skip It

No device is right for everyone. Here is an honest breakdown.

It suits:

• Smokers moving to vaping who want some headroom. You can start at low wattage with a salt liquid and increase the power as you adjust.
• Existing vapers who want a rugged backup or daily carry. The tough construction and decent battery make it a sensible device for commutes, work sites and weekends away.
• People who like a looser draw but do not want a bulky tank. The kit gives a restricted direct-to-lung option in a pocketable form.
• Anyone who wants to control running costs. A refillable kit with a 10ml bottle costs far less per puff than a stream of single-use devices, and you choose the flavour.
• Vapers who like adjusting settings. The variable output lets you tune flavour and throat hit for different liquids.

You might want to skip it if:

• You want the absolute smallest device. This kit is thicker and heavier than a slim pod.
• You want a fit-and-forget experience. Refilling, priming and changing coils takes a little learning and a little mess.
• You only ever vape lightly, in short bursts. A smaller, simpler pod will do the job at lower cost.
• You want a very large tank. UK rules cap pod size at 2ml, so heavy vapers will refill often.
• You are looking for sub-ohm cloud production. A 45W pod kit is not a replacement for a dedicated mod and tank.
• You do not already smoke or vape. Nicotine is addictive, and this product is for adults who are already using nicotine.

You must be 18 or over to buy or use this product in the UK, and we may ask for age verification on delivery. If you are pregnant, have a heart condition or are taking medication, speak to your doctor before using nicotine products.

One more consideration is experience level. A complete beginner can use the Hero 2, but the number of settings can feel like a lot at first. If you are brand new, set it to a low wattage, use a 10mg to 20mg salt liquid, and leave it alone for a week before you start adjusting. If you are a returning vaper, you will probably feel at home within a day.

How to Fill, Power On and Use the Kit

Setting up the kit takes a few minutes. Follow these steps in order for the cleanest start.

• Charge first. Plug the device into a USB-C charger and let it charge fully before first use. This sets the battery up properly and gives you a baseline.
• Fit the coil. Push the coil firmly into the pod until it seats fully. A loose coil leaks.
• Fill the pod. Open the fill port, tilt the pod, and run the nozzle of the bottle down the inside wall. Fill to just below the maximum line, and avoid the central air tube. Close the port firmly.
• Wait. Leave the filled pod for 5 to 10 minutes so the coil soaks fully. This is the most important step, and the one most people skip.
• Insert the pod. Slide or click it into the device until it seats.
• Switch on. Press the fire button rapidly the number of times shown in the manual, usually three to five clicks, to turn the device on. The display lights up.
• Set your power. Choose a low starting power, such as 20W to 25W, for the first few puffs.
• Take gentle first puffs. Use short, soft draws with a pause of around 30 seconds between them for the first few puffs, then move to your normal rhythm.

To switch off, use the same rapid-press sequence. Do this whenever the kit goes into a bag or pocket, as it prevents accidental firing.

To change the power, follow the button combination described in the manual. It is quick once you have done it a few times. Increase in small steps, 2W to 3W at a time, until the flavour and throat hit suit you, then leave it.

Refilling is straightforward. When the liquid level drops to about a quarter, top it up. Do not wait until the pod is empty, because a dry coil burns quickly and the damage cannot be reversed. After a refill, give it a minute before the next puff.

Cleaning is minimal. Wipe the pod base and the device contacts with a dry tissue or cotton bud when you refill. Never use water on the contacts, and do not run the pod under a tap with the coil in place.

If you switch flavours, empty the pod, wipe it out and fit a new coil. Rinsing the pod with warm water is fine if you leave it to dry fully before refilling, but the coil must never be rinsed and reused.

Travelling is simple. Switch the device off, keep the pod at least half empty if you are flying, because pressure changes can push liquid out, and keep the kit in a bag rather than loose. Check the airline rules, as vaping devices usually must go in the cabin, not in hold luggage.

Troubleshooting Common Problems

Most problems with pod kits have simple fixes. Work through these before you assume the device is faulty.

Burnt or dry taste. The commonest cause is a coil that has not been primed, or a pod that is running low. Refill, wait, and take gentle puffs. If the taste stays burnt after a proper prime, the coil is likely spent. Replace it. Sweet liquids and high power both shorten coil life, so reduce the wattage a notch with the new coil.

No vapour, or weak vapour. Check that the pod has liquid, the coil is seated, and the contacts are clean. Remove the pod and wipe both sets of contacts. Look at the airflow path for a block. If you have just changed the coil, make sure it has soaked. A thick, high-VG liquid can also starve a low-power coil, so try a 50/50 blend.

Leaking. Leaks usually come from over-filling, a coil that is not fully seated, a worn gasket or temperature and pressure changes. Fill only to the maximum line, push the coil in until it sits flush, and close the fill port fully. Carrying the device upright, switched off, helps. If the leak continues with a new pod and coil, the pod seals are the likely culprit.

Gurgling or spitting. Condensation or flooding in the coil chamber. Remove the pod, blow gently through the mouthpiece to clear the airway, and wipe away any pooled liquid. Lower the wattage slightly. Gurgling that returns often points to over-filling.

Error messages on the display. Messages relating to a missing or short-circuited coil usually mean dirty contacts or a coil that is not seated. Clean the contacts, reseat the coil and try again. If the message persists with a known good coil, the coil may be faulty, so try another.

Device will not charge. Try a different cable and a different charger, and check the port for lint. A torch and a wooden toothpick will clear pocket fluff from a USB-C port. Do not use metal tools. If it still will not charge, contact us. Never try to open the casing.

Device will not fire. Check it is switched on, unlocked, and charged. A completely flat battery needs a few minutes on charge before it responds.

Hot device. If the body gets uncomfortably hot, stop using it, let it cool, and check the coil and wattage. Persistent heat suggests a fault. Stop using it and contact us.

Throat irritation. This is usually the nicotine strength or the wattage. Lower either, and consider a smoother salt liquid.

If you have tried everything and the kit still misbehaves, contact us with your order number and a short description of the fault. We will help with warranty and returns.

Value for Money and How It Compares

Value is more than the price on the tag. For a pod kit it comes down to what you pay upfront, what you pay each week to run it, and how long the device lasts. By those measures the H45 Hero 2 looks sensible.

The upfront price sits above a basic starter pod and below a full mod-and-tank setup. For that you get a battery that goes through most of a day, a rugged shell and a flexible power range. Running costs depend on your liquid and your wattage, but a 10ml bottle of nicotine salt liquid and a pack of coils costs a fraction of what a heavy user would spend on single-use devices over the same period. Coils are the main ongoing expense, and at one to two weeks per coil a pack of coils goes a long way.

It is fair to compare the kit with its rivals. Here are the ones buyers usually weigh it against, in broad terms.

• Vaporesso XROS series: smaller, lighter and more pocketable, with lower power output. A good choice for tight, cigarette-like MTL vaping. It does not have the power range of the Hero 2, and some users find the battery runs out sooner. If you want the smallest possible device, the XROS wins. If you want power headroom and a tougher shell, the Hero 2 does.
• Uwell Caliburn series: a long-standing favourite with a simple interface, a slim body and a tight draw. Power output is lower, and the battery is smaller. It suits someone who wants simplicity. The Hero 2 suits someone who wants adjustment.
• OXVA Xlim series: a strong rival with a slim profile and a range of coils. Output is lower than the Hero 2 on most models, and the build is lighter. The Hero 2 feels sturdier, and the Xlim is easier to carry.
• SMOK Novo series: broadly similar in concept, with differences in pod design and coil range. Check current coil availability and price before you choose, since the cost of coils is what decides long-term value.
• Larger Geekvape mod-style kits, such as those in the Aegis Legend and Aegis Boost lines: bigger, more powerful and more capable of sub-ohm vaping. They cost more and weigh more. If you want clouds, they are the better fit. If you want a pocket device, the Hero 2 is the more practical choice.

Where the Hero 2 is weaker: it is bulkier than the slimmest pods, the 2ml UK pod needs frequent refills at high power, and the interface asks you to learn a few button presses. Where it is stronger: build quality, power range, battery size for its class and flavour from the mesh coil.

Our verdict is straightforward. If you want a tough, adjustable pod kit that covers both MTL and light restricted direct-to-lung vaping, it is good value for money. If you only want the simplest, smallest device, buy one of the slimmer options instead. Whichever way you go, the real saving comes from a refillable kit over repeated single-use purchases, and from recycling the old device properly when its time comes.