SMOK R Kiss 2 Starter Kit 200W Black

Overview

The SMOK R Kiss 2 Starter Kit 200W Black by Smok in Black at 0mg. Free UK delivery over £20, same-day dispatch on weekday orders before 4pm.

SMOK R Kiss 2 Starter Kit 200W Overview

The SMOK R Kiss 2 Starter Kit 200W is a reusable, rechargeable vape kit built around a dual 18650 battery layout and a maximum output of 200 watts. It sits in the part of the market occupied by high-wattage pod mod kits: larger and more powerful than a pen-style pod system, but simpler to run than a full box mod with a separate sub-ohm tank. If you have outgrown a small pod kit because the vapour feels thin or the battery is flat by mid-afternoon, this is the sort of device many vapers look at next.

SMOK has been making vaping hardware for well over a decade, and the R Kiss line has been one of its recurring pod-mod formats. The 2 in the name marks the second generation, which builds on the first with a wider power range and a pod and coil system aimed at flavour-focused, lung-style vaping rather than tight mouth-to-lung draws. The 200W figure is a ceiling, not a target. Most people will spend their time well below it, and the extra headroom mainly means the device is not working at its limit during normal use.

This page covers what the kit is, how it performs, what it is like to live with, and where it makes sense compared with the alternatives. Where we describe features, we describe them in general terms that hold across the range, and we point you to the specification table on the product listing for any figure that can differ between production batches or regional versions, such as pod volume and the exact coil sizes supplied in the box.

A few quick points before the detail:

• Reusable device: this is a refillable kit, not a disposable. It uses replaceable coils and takes the e-liquid of your choice.
• Batteries: the device uses two 18650 cells. These are normally sold separately and are not part of the kit, so budget for them.
• Adults only: vaping products are for adult smokers and existing vapers aged 18 or over. If you do not smoke, you should not start.
• UK rules apply: in the UK, nicotine e-liquid strength is capped at 20mg/ml, nicotine refill bottles are limited to 10ml, and tanks and pods are limited to 2ml. Shortfill bottles with nicotine added through shots are a separate, common route to larger volumes at low strength.

What Comes in the Box and What You Need to Buy Separately

Starter kits vary slightly between versions and retailers, so always compare the contents listed on the product page with what you expect. As a general guide, a kit of this type includes the main device, a refillable pod, at least one coil (often with a spare), a USB charging cable and printed paperwork such as a user manual and warranty card.

What it does not normally include is the pair of batteries. This catches out first-time buyers more than any other point in the process. Dual 18650 devices are designed to run on removable lithium-ion cells, and for safety and shipping reasons they are usually listed separately. Before you click buy, make sure you have two matching high-drain 18650 batteries ready, or add them to your order.

Here is a sensible shopping list for your first day:

• The SMOK R Kiss 2 kit itself.
• Two genuine high-drain 18650 batteries from the same brand and the same batch, with a continuous discharge rating of 20A or higher. Buy from a reputable seller and avoid bargain cells with unclear branding, because counterfeit batteries are a genuine safety concern.
• An external battery charger with 18650 bays, if you intend to charge outside the device. Many vapers prefer this because it is gentler on the cells and lets them rotate a spare pair.
• Battery cases or silicone sleeves for carrying spare cells. Loose batteries should never travel in a pocket or bag alongside keys or coins.
• A bottle of e-liquid suited to higher-power vaping (see the nicotine and flavour sections below).
• A few spare coils so you are not caught short midweek.

Check the battery wraps every time you swap cells. A torn or damaged wrap can expose the metal casing and cause a short circuit. If the wrap is damaged, stop using that cell and either have it rewrapped by a qualified supplier or recycle it. Never keep using a damaged battery to save a few pounds.

The kit is offered in several finishes, and the listing shows seven variants in this range. The colour or finish you choose does not change the electronics, so pick whichever you like the look of. The variant selector on the product page shows which options are currently in stock.

Power Output and Real-World Performance

The headline number is 200 watts, and it is worth being clear about what that does and does not mean. Wattage is the electrical power delivered to the coil. Higher wattage heats the coil faster and vaporises more e-liquid per second, which gives a larger, warmer cloud and a stronger flavour per puff. It is not a quality score. A 200W ceiling simply tells you how much room the device has to drive a low-resistance coil hard.

In practice, every coil is designed around a recommended range, usually printed on the coil body or the packaging. A typical mesh coil intended for lung-style vaping runs comfortably somewhere between roughly 40 and 90 watts, depending on its resistance and your taste. Only very low resistance coils built for high power make use of the top end of the range. Run a coil well above its rated range and you will taste burnt cotton, shorten its life and waste e-liquid. The sensible habit is to start at the low end of the printed range, take a few puffs, and raise the power in small steps until the flavour is full without becoming harsh.

What you can reasonably expect from a 200W-class kit:

• Fast ramp-up: the coil reaches working temperature quickly, so there is little delay between firing the device and getting vapour.
• Consistent output: dual-cell devices like this typically wire the cells in series, so the voltage stays steadier under load than on a small internal battery. That helps avoid the fade you sometimes notice on compact pod kits as they drain.
• Room to adjust: adjustable wattage lets you tune the same coil from a cooler, gentler vape to a warmer, denser one without swapping hardware.
• Longer gaps between charges: a pair of 18650s at moderate wattage generally lasts a full day for many users, though heavy use at high power will drain them faster.

Puff count is a figure usually quoted for disposables, and it does not translate neatly to refillable kits. How many puffs you get depends on the pod capacity, your wattage and the length of your puffs. With a 2ml pod, expect each fill to give a few hundred puffs at moderate settings, with higher wattage using liquid faster. Anyone quoting an exact puff number for a refillable kit is estimating.

One more practical point: more power is not automatically better. On 200W-capable hardware, the sweet spot for most people is in the middle of the range. If you find yourself constantly at the maximum, the coil is probably too low in resistance for your taste, or your e-liquid is too thin for the way you vape. Try a different coil before you try a different device.

Pod and Coil Technology

The R Kiss 2 is a refillable pod-mod system, which means the e-liquid is held in a removable pod and a replaceable coil sits inside it. This format gives you most of the convenience of a closed pod kit, since there is no separate tank to disassemble, while still letting you choose your own e-liquid and swap coils when one wears out.

Coils for this style of device are typically mesh. A mesh coil is a thin sheet of metal mesh rolled into a cylinder, rather than a single wire wrapped around a cotton wick. The larger surface area has a few practical effects:

• More even heating: the e-liquid is heated across a wider area, which tends to produce a rounder, more consistent flavour from the first puff to the last.
• Quicker response: mesh heats up fast, so you do not wait for the coil to catch up with the power you have set.
• Lower resistance options: mesh makes it practical to build coils with very low resistances, which is how a device can usefully deliver a high wattage.

The trade-off is that mesh coils are sensitive to the way you treat them. Three habits extend their life considerably. First, prime every new coil: drip a few drops of e-liquid directly onto the cotton through the intake holes, fill the pod, and let it sit for around ten minutes before you fire it. Second, never fire the device with an empty or nearly empty pod, since a dry coil burns almost instantly. Third, match the e-liquid to the coil. Very sweet, thick liquids with a high VG ratio gunk up a coil faster than thinner, more balanced liquids.

Expect a coil to last somewhere between one and three weeks of regular use. That range is wide because it depends on your wattage, your e-liquid and how often you vape. The clear sign that a coil is finished is a flat, muted or slightly burnt taste that does not clear after a fresh fill and a short rest.

A note on volume: UK regulations limit refillable tanks and pods to 2ml, so the pod you receive in a UK-supplied kit will hold 2ml regardless of what larger international versions of a device may carry. Check the product specification on the listing to confirm what is supplied. Only use coils that match the series and resistance stated for the device, and buy replacements from the same brand family so the fit and the wattage range are correct.

Flavour Profile and E-Liquid Pairing

The kit itself has no flavour of its own, so this section is about getting the most from the e-liquid you choose. The seven variants listed for this product are finishes of the same hardware, not different flavours. What you taste depends entirely on the bottle you fill it with.

A mesh coil running at moderate to high power rewards e-liquids with defined top notes and a clean finish. Here are the flavour families that tend to work well and why:

• Menthol and mint: cooling profiles come through crisply on mesh, and a good menthol e-liquid stays smooth rather than harsh when the power is set sensibly. A popular choice for people moving away from menthol cigarettes.
• Blueberry ice: a well-known pairing, with the fruit holding up against the cooling agent even as the coil heats up.
• Strawberry watermelon: light, juicy fruit blends are easy on a high-airflow setup and are rarely cloying.
• Mango: tropical flavours have a lot of body, which suits the denser vapour of a higher-power device.
• Cola: carbonated-style profiles with a citrus edge show the sharper end of what mesh can deliver.
• Vanilla custard and bakery blends: richer dessert profiles work, but they are heavier on the coil, so expect to change coils a little sooner.
• Tobacco: a gentle tobacco or tobacco-and-nut profile is a reasonable choice if you want something familiar. Dark, heavily sweetened tobaccos can taste muddy at high wattage.
• Mixed berries: blends of raspberry, blackcurrant and blueberry give a layered flavour that the even heating of mesh handles well.

Think about the VG and PG split on the bottle. Most shortfill and 50/50 style e-liquids are built for different hardware. A 70VG/30PG liquid is the usual match for a sub-ohm or high-power mesh coil: it produces more vapour and wicks well into the larger cotton surface. A 50VG/50PG liquid is thinner, carries flavour sharply and is the usual choice for tighter-draw pod kits. If you use a thin 50/50 liquid at high power you may see the coil leak or spit.

Finally, remember that high wattage lifts the flavour intensity but also consumes the bottle fast. Many people find that dropping the power a few watts gives a noticeably better balance of taste and value, even on a kit that could do much more.

Design and Build Quality

Dual 18650 devices are bigger than pen-style pod kits, and the R Kiss 2 follows that formula. You should expect a rectangular or softly contoured body of a size comparable to other dual-cell pod mods: comfortable in an adult hand, noticeably heavier than a pod kit, and not something that vanishes into a skinny jeans pocket. The weight is mostly the two cells, and with batteries installed the device feels more solid and balanced than its lighter rivals.

The body of SMOK devices in this class is normally a zinc alloy or similar metal construction with a lacquered or coated finish. Metal gives a reassuring weight and handles knocks better than plastic, though the paint or coating can chip at the edges over time, especially if the device lives in a pocket with keys. A silicone sleeve or a small carry case is a cheap way to keep the finish tidy.

Day-to-day, these are the design points that matter:

• Display and controls: a small screen shows wattage, battery level and often coil resistance, with a few buttons to adjust settings. It takes a few minutes to learn the button sequence for locking the device and changing power, and the manual covers it.
• Battery door: access to the cells is usually through a sliding or hinged door or a screw-off panel. Check that the door closes firmly every time. A loose door causes intermittent firing.
• Pod fit: the pod should click or seat firmly in the device. If it feels loose, remove it and check the contacts for liquid residue.
• Airflow: an adjustable airflow slot lets you tighten the draw for a more restrictive feel or open it for a looser, cooler vape. Experiment with it alongside your wattage, since the two settings interact.
• Fill port: a side or top fill port is normal on pod mods of this type. Fill slowly and stop below the top to avoid flooding the airflow channel.

On build quality, the sensible expectations for this class are consistent fit and finish across the body, no rattling when the device is shaken, and a firm seat for the pod and the battery door. If you receive a unit with a loose panel, a screen that flickers or buttons that stick, contact the shop straight away rather than living with it. Those faults are covered under consumer law and under the manufacturer warranty.

Compared with disposable vapes, the build is in another league for durability, since this is hardware intended to last many months or years with consumables replaced along the way.

Battery and Charging Guidance

Because the R Kiss 2 uses two removable 18650 cells, battery care matters more than it does with a sealed internal battery. A little discipline here is the difference between a kit that runs reliably for years and one that causes problems.

Start with the cells. A typical high-drain 18650 has a capacity in the region of 2,500 to 3,500mAh. Because dual-cell devices usually place the cells in series, the capacity of the pair is roughly that of a single cell, while the voltage is doubled. In other words, do not add the two figures together. What matters is that both cells are matched, have the same rating, and are charged and used as a pair. As a rule of thumb, a 3,000mAh pair at moderate wattage should comfortably get a typical day of vaping, though your own usage will vary.

Safe battery habits that every user of a removable-cell device should follow:

• Buy only genuine cells from a reputable retailer, with a continuous discharge rating suited to the device. Ignore inflated capacity claims on unbranded cells.
• Always use the cells as a matched pair, and keep each pair together. Do not mix old and new batteries or different brands.
• Inspect the wrap before each swap. If there is any tear, dent or damage, retire the cell.
• Never leave batteries charging unattended or overnight, and never charge on a soft surface such as a bed or sofa.
• Do not carry loose cells in a pocket or bag. Use a plastic or silicone case.
• Keep cells away from heat, including cars on warm days and radiators.
• Stop using any cell that gets unusually hot, swells, leaks or smells odd.

Charging can usually be done in two ways: with the cells in the device via the USB cable, or removing them and charging in an external charger. Charging inside the device is convenient. An external charger is generally better practice for long-term battery health, because it gives you an accurate display of the charge state and lets you rotate spare pairs. If you charge in the device, use a quality charger and cable rather than a high-output fast charger, which can run hotter.

At the end of their life, 18650 batteries should never go in household rubbish or ordinary recycling. Take them to a battery drop-off point, which many supermarkets and council household waste recycling centres provide. Retailers that sell vaping products also commonly accept used devices and batteries for recycling. Tape the terminals of spent cells before you drop them off.

Nicotine Strength Guidance

The kit does not contain nicotine; the e-liquid you add does. In the UK, nicotine e-liquid is capped at 20mg/ml, and nicotine refill bottles are capped at 10ml. The right strength for you depends on the type of nicotine in the bottle, the way you vape, and how much you smoked previously.

High-power devices with mesh coils are a different proposition from tight-draw pod kits. They deliver a lot of vapour per puff, which means you take in more nicotine per puff than you would from the same strength liquid on a low-power device. As a result, the strengths people choose are normally lower:

• 0mg: nicotine-free. A sensible option for people who have already stopped nicotine or who vape purely for the flavour.
• 3mg freebase: the usual starting point for large-cloud, lung-style vaping on a 70VG liquid. Gentle on the throat and suits moderate to heavy puffers who want a light nicotine level.
• 6mg freebase: a middle option for former moderate smokers who find 3mg unsatisfying. At high wattage it can be noticeably harsh in the throat.
• 10mg to 12mg nicotine salt: a smoother alternative if you want a stronger nicotine hit without the throat harshness of freebase. Better suited to lower or moderate wattage.
• 18mg to 20mg nicotine salt: aimed at tight, low-power devices, and generally too strong for a high-wattage kit unless you take very short, infrequent puffs. If you are coming off 20 cigarettes a day and want the higher strength, run the kit at the lower end of its power range.

A quick rule of thumb: the more power and airflow you use, the lower the strength you need. If you feel dizzy, nauseous, sweaty or you get a pounding heart, you have taken too much nicotine. Stop, drink water and step down a strength next time.

Shortfills are 0mg bottles of 50ml or 100ml with room to add nicotine shots. Add a shot and you can reach around 3mg while keeping the larger bottle format. They are a cost-efficient way to run a high-power kit, but they need a little care to mix. Shake well after adding a shot and let the bottle rest for a day if possible.

If you are using vaping to quit smoking, speak to a local stop smoking service or your pharmacist. They can give you free, personalised support and can help you taper your nicotine over time.

Who the SMOK R Kiss 2 Is For, and Who Should Skip It

No device suits everyone. Here is an honest view of where this kit fits and where it does not.

It is a good match if you:

• Are an adult smoker or existing vaper who wants a bigger, more satisfying vape than a small pod kit delivers.
• Enjoy lung-style inhales and want denser vapour with a defined flavour.
• Are comfortable handling and charging removable 18650 batteries safely.
• Want to choose your own e-liquid from a wide range of shortfills and nicotine salt bottles, rather than being locked to a manufacturer's pods.
• Value a replaceable-coil system that costs less per day than single-use products over time.
• Want a device with room to grow, where you can lift or lower the power as your tastes change.

You should probably look elsewhere if you:

• Are new to vaping and want the simplest possible experience. A pre-filled pod system or a compact refillable pod kit with fixed settings is easier to learn.
• Want a tight, cigarette-like mouth-to-lung draw with high-strength nicotine salts. A 200W mesh device is designed for the opposite style, and a low-power pod kit will suit you better.
• Prefer something truly pocketable. Dual 18650 kits are bulky and heavy by comparison.
• Do not want to deal with batteries. Removable cells require a small amount of care that a sealed-battery device does not.
• Are not a smoker or existing nicotine user. Vaping is not recommended for non-smokers, and it is illegal to sell vaping products to anyone under 18 in the UK.
• Are on a very tight budget for accessories. Remember that batteries, a charger and spare coils add to the starting cost.

Think about how you will actually use it. If you vape heavily at home or at work and are fine carrying a slightly larger device, the extra battery and power headroom make sense. If you want something you can slip into a small pocket on a night out, a smaller kit will do the job with less fuss.

How to Set Up and Use the Kit

Setting up a new kit takes about fifteen minutes, most of which is waiting for the coil to soak. Follow these steps in order for a clean start.

• Check the box: make sure the device, pod, coils, cable and paperwork are all present, and examine the device for damage.
• Fit the batteries: open the battery door, check the wraps on both cells, and insert them with the positive and negative ends facing the way the markings inside the compartment show. Close the door firmly.
• Prime the coil: install the coil in the pod following the manual, drip a few drops of e-liquid onto the cotton through the intake holes, then fill the pod to just below the top through the fill port.
• Wait ten minutes: this lets the cotton soak fully. Skipping this step is the most common reason a new coil tastes burnt.
• Seat the pod: push the filled pod into the device until it clicks into place.
• Switch on: most devices of this type use five rapid presses of the fire button to power on and off. Check the manual for the exact sequence on your unit.
• Set the power: start at the low end of the range printed on the coil, then adjust upward using the plus and minus controls.
• Take gentle first puffs: take a few short puffs with a pause between each to allow the wick to refill. The first couple of puffs on a new coil are often a little mild.
• Tune the airflow: open or close the airflow ring to change the draw. A looser draw suits higher power and a tighter draw is more cigarette-like.

For daily use, keep a rhythm: top up the pod before it runs low, rest between puffs for a few seconds, and avoid chain vaping at maximum power, which overheats the coil and dries the wick faster. When you swap e-liquid flavours, either use up the old liquid first or change the coil, since coils hold on to the flavour of the previous liquid.

Cleaning is straightforward. Wipe the pod contacts and the device connectors with a dry cotton bud now and then, since liquid residue is a frequent cause of poor connections. Rinse the pod in warm water only when you are changing the coil and let it dry fully before refilling.

Troubleshooting Common Problems

Most problems with pod-mod kits have simple causes. Work through this list before assuming the device is faulty.

• Burnt or harsh taste: the usual causes are an unprimed coil, a pod running low, power set too high for the coil, or a coil that has reached the end of its life. Re-prime, refill, drop the wattage by 5 to 10 watts, and if the taste does not improve, replace the coil.
• Weak vapour or muted flavour: a worn coil is the most likely culprit, followed by a very sweet liquid that has gunked the cotton. Try a fresh coil. If you were using a thin liquid, check you are not flooding the airflow.
• Device does not fire or shows a check atomizer message: take the pod out, wipe the contacts and reseat it firmly. If the message persists, try a new coil, since the current one may have failed.
• Low battery message with charged cells: check the cells are seated correctly and the battery door is fully closed. Dirty contacts in the battery compartment can also cause this, as can worn or low-quality cells that sag under load.
• Leaking pod: overfilling is the common cause, along with using very thin liquid, a loose coil, or the pod not being fully seated. Fill to just below the top, ensure the coil is screwed or pressed in firmly, and store the device upright when you can.
• Gurgling or spitting: this is condensation in the airflow path or a flooded coil. Hold the device upside down, blow gently through the mouthpiece to clear the chimney, and wipe off any excess.
• Intermittent firing: loose battery door, unclean contacts or a loose pod are the likely causes. Clean and reseat.
• Dry hits: the wick is not getting enough liquid. Refill, let the pod rest, take shorter puffs with breaks between, and check that the wattage is within the coil rating.
• Device stuck on a lock or error screen: remove the batteries for a minute and reinsert them. Consult the manual for the lock sequence if the buttons seem unresponsive.

Never keep using a device that gets very hot in your hand, smells of burning plastic, or has a battery that is swelling or venting. Remove the cells if it is safe to do so, move the device away from anything flammable and contact the shop or the manufacturer.

If you have tried the steps above and the fault remains, contact the shop with your order number and a description or photo of the problem. A genuine fault in a new device is covered under UK consumer rights and the manufacturer warranty.

Value for Money and How It Compares

The fairest way to judge value is to look at the full cost of ownership, not the sticker price alone. A starter kit is a one-off cost, but then you pay for batteries, coils and e-liquid. Compared with buying disposable vapes daily, a refillable kit usually works out cheaper within a few weeks if you vape regularly, and it generates far less waste. That matters even more in the UK now that single-use vapes have been banned from sale, which has pushed many former disposable users towards refillable kits like this one.

Where does the R Kiss 2 sit against the alternatives? Here is a fair comparison of the main routes, without claiming any one is right for everyone:

• Compact pod kits such as the SMOK Nord line or the Uwell Caliburn range: far smaller, simpler and better suited to tight, cigarette-like draws with nicotine salts. They cannot match a 200W device for vapour volume or battery runtime, but they are easier to carry and use.
• Vaporesso GEN 200 and similar dual 18650 pod mods: the closest rivals in format and power. Differences come down to coil ecosystem, screen layout, button feel and finish. Both approaches deliver similar results at similar wattages, so coil availability and price per pack are practical tie-breakers.
• Geekvape Aegis Legend 2 and rugged dual-cell mods: built for a tougher use case, with water and shock resistance and a separate sub-ohm tank. They are bulkier and offer more tank volume on international models, but the UK 2ml cap evens that out.
• Freemax Maxus 200W and other dual 18650 kits: similar in concept, with a choice of coils and tanks. Check the coil cost and availability in your area before committing.
• Disposables: the cheapest way in, but they cost more over time and create waste. Rules now restrict single-use vapes in the UK, and a reusable kit is the longer-term option.

These are general comparisons, and models change from year to year, so check current specifications before you decide. Where the SMOK kit makes a solid case is for people who already know they want a 200W-class format and who like SMOK's coil range, which is widely stocked in UK shops and easy to replace.

To keep running costs down, buy coils in multi-packs, use shortfills rather than 10ml bottles if you go through a lot of liquid, and avoid running at maximum wattage when a lower setting tastes just as good. Look after the batteries and they will last through hundreds of charge cycles.

When the kit finally reaches end of life, do not put it in the bin. Vaping devices and batteries count as electrical and battery waste and can be taken to a recycling drop-off point or returned to participating retailers. Drain the pod, remove the cells and recycle each part appropriately.