Vaporesso Armour Max Vape Kit Cyber Gold

Overview

The Vaporesso Armour Max Vape Kit Cyber Gold by Vaporesso in Cyber Gold at 0mg. Free UK delivery over £20, same-day dispatch on weekday orders before 4pm.

Vaporesso Armour Max Vape Kit overview

The Vaporesso Armour Max Vape Kit is a high-output, dual-battery sub-ohm kit for vapers who want dense vapour, a tough device and room to adjust their own settings. It pairs a rugged mod, rated for up to 220W, with a refillable mesh-coil tank, and it is built for direct-lung (DTL) vaping. That means a long, open, relaxed inhale straight to the lungs, rather than the tight, cigarette-style draw you get from a small pod kit or a mouth-to-lung tank.

The Armour Max is a reusable system in every sense. It runs on two removable 18650 cells (sold separately), it takes a tank you fill from a bottle of e-liquid, and it uses replaceable coils. After the initial purchase your running costs are e-liquid, the occasional coil and, every year or two, a fresh pair of batteries. For UK buyers it is also a legal, practical alternative to single-use devices, which have been banned from sale across the UK since 1 June 2025.

This guide goes through what you actually get: specifications, performance, flavour, build, battery behaviour, coil technology, nicotine strength, who the kit suits and who should look elsewhere, setup, troubleshooting and value. We also compare it fairly with a few direct rivals, because a kit in this class is only worth buying if it holds up against them.

In short:

• Strengths: generous power headroom, replaceable cells, mesh coils with an even heat spread, a sturdy body and a straightforward interface.
• Trade-offs: it is bigger and heavier than a pod kit, batteries are an extra purchase, and the 2ml UK tank means more frequent top-ups than the larger tanks sold in some other countries.
• Suited to: existing vapers stepping up from pods, or ex-smokers who have found small devices unsatisfying.

You must be 18 or over to buy or use this product. It is intended for adult smokers and vapers, not for non-smokers or young people.

Key specifications at a glance

Below are the headline figures for the kit. They reflect Vaporesso's published specifications for the Armour Max range. The tank and coil supplied in the box can vary slightly by production batch and variant, so treat the product listing and the printed manual as the final word on exact part codes.

• Maximum output: up to 220W, adjustable in small steps.
• Power source: two removable 18650 lithium-ion cells, not included. They run in series, which is how the mod reaches its higher wattage ceiling.
• Charging: USB-C port on the mod for in-device charging, with the option of an external charger for the cells.
• Tank: refillable sub-ohm tank with top-fill access and adjustable airflow. UK law limits tank capacity to 2ml, so the UK edition holds 2ml. Larger capacities seen on overseas listings are not sold here.
• Coils: replaceable Vaporesso mesh coils, with resistances typically in the 0.15 to 0.4 ohm band across the compatible range.
• Vaping style: direct-lung (DTL), open airflow, large vapour output.
• Connection: standard 510 thread, so the mod will accept many other 510 tanks as well.
• Output modes: variable wattage plus additional modes controlled by Vaporesso's chipset. Mesh coils are normally used in plain wattage mode.
• Safety protections: short-circuit, low-resistance, over-temperature and low-voltage protection, which is standard on regulated mods of this class.
• E-liquid: not included. Choose a 70VG/30PG or 50VG/50PG liquid for sub-ohm tanks.
• Minimum age: 18.

Two practical notes follow from those numbers. First, 220W is the ceiling the electronics can reach, not a recommended setting. Almost nobody vapes a mesh coil anywhere near that figure, and doing so would empty a 2ml tank in minutes and burn through a coil in days. Second, the two cells are wired in series, so they are always discharged together and must be a matched pair: same brand, same model, same age, and charged together.

Performance and vapour delivery

Performance on a kit like this is about power headroom, firing response and how consistent the output stays as the batteries drain. The Armour Max is a regulated mod, so the chipset holds your chosen wattage steady until the cells approach empty, rather than letting output sag gradually. A coil set to 60W gets 60W on the first puff after charging and on the last puff before the low-battery warning.

Firing is quick. Press the button and the coil reaches working temperature within a fraction of a second, which matters more than it sounds: on a slow-firing device you tend to hold the button longer, wasting power and heating the liquid unevenly. Mesh coils also help here, since the large surface area warms evenly rather than concentrating heat in one spot.

In practical terms, here is what to expect at different power levels with a typical 0.2 ohm mesh coil:

• 40 to 55W: warm, flavour-focused vapour with moderate cloud size. This is the zone where many ex-smokers settle, and it is gentler on both liquid and batteries.
• 55 to 75W: fuller, warmer vapour with a more obvious throat hit and noticeably denser clouds. Most users who want visible vapour from this kit end up here.
• 75W and above: hot, heavy vapour, shorter coil life and rapid liquid use. Fine as an occasional experiment, but it is not where mesh coils are at their most pleasant.

Run time depends on your settings, but a rough estimate helps. A fresh pair of 3,000mAh cells in series holds roughly 22 watt-hours. At 60W, with three-second puffs and normal conversion losses, that works out to somewhere in the region of 300 to 400 puffs per charge. At 40W the same cells stretch well beyond that; at 90W expect around half as many. These are estimates, not laboratory figures, and real results vary with cell quality and age.

Liquid use is the other side of the equation. A 2ml tank at 60W typically lasts somewhere between 150 and 300 puffs, depending on puff length and how thick the e-liquid is. Heavy users therefore refill several times a day, which is the main practical cost of the UK tank limit. If you find yourself refilling every hour, drop the wattage by 5 to 10W and see whether the vapour still satisfies you.

Throat hit is set mainly by your nicotine strength and the PG ratio of the liquid, not by the device. The Armour Max itself delivers smooth, wide-open vapour. If it feels harsh, the cause is usually too much power for the coil or too much nicotine for direct-lung inhalation.

Flavour and e-liquid pairing

A kit does not come with flavour built in, so flavour quality depends on two things: how well the coil vaporises liquid, and the liquid you choose. The mesh coils in this class are well regarded for clean, consistent flavour because the wide mesh surface heats evenly and turns liquid to vapour without overheating small patches of it. The result is a flavour that holds steady from the first puff to the last, instead of fading or turning toasted halfway through the tank.

The ten variants listed for this kit are finish options of the same device, not different flavours, so choose between them on look and availability. Performance is identical.

Here are flavour styles that suit sub-ohm mesh coils, which is where this tank does its work:

• Menthol and mint: crisp, clear and easy on the coil; a sensible first choice for ex-smokers who miss a menthol cigarette.
• Blue raspberry ice: bright fruit with a cooling finish that carries well at moderate wattage.
• Strawberry kiwi: a familiar fruit blend that stays recognisable even at higher power.
• Cola and cherry cola: sharp, fizzy profiles that show off mesh clarity.
• Mango and peach ice: juicy, rounded fruit that benefits from the warm vapour of 55 to 70W.
• Vanilla custard and bakery profiles: rich and smooth, but sweeter liquids gunk coils faster, so expect shorter coil life.
• Tobacco: a dry, light-brown tobacco note can feel closer to smoking, though some find it thin at sub-ohm power. Try a 50VG/50PG blend.
• Lemon sherbet and citrus mixes: zesty and bright, with a light vapour that suits lower wattage.

Some tips to get more from any flavour:

• Pick a 70VG/30PG liquid for thicker clouds, or 50VG/50PG for stronger flavour and a firmer throat hit. Very high-VG liquids (80VG or more) can wick slowly and may cause dry hits.
• Lower the wattage for more flavour. Higher power gives larger vapour but flattens subtle notes. In most cases the sweet spot is the middle of the range printed on the coil.
• Do not chain vape. Give the coil a few seconds between puffs so the wick can re-saturate.
• When switching flavours, empty the tank, rinse it and swap the coil if you are moving from a strong flavour such as menthol to something delicate. Old flavour lingers in the cotton.

Design and build quality

The Armour line takes its name from its construction approach, and the Armour Max follows the pattern: a sturdy chassis, a textured grip that stays secure in the hand, and a firing button large enough to find by feel. It is a deliberately practical design. It is not slim and it is not pocket-discreet, but it is built to cope with being carried in a work bag, dropped on a van floor or passed around on a night out.

Size and weight are what you would expect from any dual-18650 mod. It is noticeably larger than a pod kit and a fair bit heavier once the cells and a full tank are in place, roughly in the region of 250 to 300 grams loaded. If you plan to vape on the move, check that your pockets or bag can handle it before committing. For those who find weight tiring, the heft also gives a reassuring, solid feel at the lips.

The interface keeps things simple. A display shows wattage, coil resistance, battery level and puff information, and a small set of buttons adjusts power up and down. There is no need for a smartphone app to get everything running. Vaporesso also supports firmware updates through the USB-C port for those who want them, and such updates are typically small refinements rather than big overhauls.

The tank follows the same sensible approach. Top-fill access removes the need to unscrew the tank, which is where most spills and leaks begin. Airflow is adjusted with a ring, and the glass section is replaceable. Small details matter here: the quality of the silicone seals, the threads that hold the base on, and how cleanly the fill port closes all affect long-term leak resistance. Check that the base is tightened fully each time you refill, and replace the O-rings if they start to look flat or cracked.

A few honest limitations:

• Do not assume any waterproof or dustproof rating. If you work outdoors, keep the device out of the rain and wipe off moisture before opening the battery bay.
• The rugged look means more mass and fewer curves than slimmer designs, and some users find the device chunky.
• Textured and coated finishes pick up scuffs with heavy use. A silicone sleeve costs a few pounds and protects the finish.
• Wide third-party tanks may overhang the mod's top plate, so check the diameter before buying one.

Overall, the build is the kind you would trust to survive daily use. The compromise is simple: portability traded for durability.

Battery life, cells and charging

This section matters more than any other, because the Armour Max is a removable-battery device and the batteries are your responsibility. The kit does not include cells. You need two 18650 lithium-ion cells from an established manufacturer, and you should buy them from a reputable UK supplier rather than an unbranded bargain listing. Fake or re-wrapped cells are the most common cause of vape battery incidents.

What to look for in a cell:

• Brand: a recognised manufacturer such as Samsung, Sony, LG or Molicel, sold by a retailer that handles genuine stock.
• Continuous discharge rating: at everyday settings of 50 to 80W, each cell supplies roughly 7 to 11A, so cells rated at 20A or more are comfortable. If you intend to run near the top of the power range, choose cells rated at 30A or higher.
• Capacity: 2,500 to 3,500mAh is typical. Higher capacity usually means a lower discharge rating, so do not choose on capacity alone.
• Matched pairs: always use two cells of the same brand, model and age, and charge them together. Do not mix old with new.

Run time works out to something like a full day for light-to-moderate use at 40 to 50W, and half a day or less at 70W and above. Carrying a second pair of charged cells makes sense if you vape heavily or travel.

Charging can be done two ways. The USB-C port on the mod charges the cells in place, which is convenient for emergency top-ups. A dedicated external charger is the better long-term option because it charges each cell independently and lets you rotate spare pairs. Whichever route you choose, allow several hours for a complete charge from empty rather than expecting a quick top-up. Use a decent-quality USB power source and cable instead of a cheap unbranded adaptor.

Basic battery safety:

• Keep the wraps intact. If the plastic wrap on a cell is torn, rewrap it or retire the cell.
• Never carry loose cells in a pocket with keys or coins. Use a plastic carry case.
• Do not charge unattended or overnight, and do not charge on a bed, sofa or other soft surface.
• Stop using any cell that gets unusually hot, swells, hisses or smells odd.
• Insert cells with the polarity marked inside the bay.

When cells reach end of life, which is typically after a few hundred charge cycles or when they no longer hold a charge, never put them in household bins. Take them to a battery recycling point: many supermarkets and DIY stores have collection bins, and household waste recycling centres accept them too. Old devices should go to a recycling centre or a retailer take-back scheme as electrical waste.

Coil and mesh technology

The performance of the Armour Max is shaped as much by its coil as by the mod. Instead of a round wire wrapped around a cotton wick, a mesh coil uses a thin sheet of metal mesh, rolled into a cylinder, with cotton pressed against the outside. That layout has several practical effects.

• Larger heating surface: liquid meets far more metal, so it vaporises faster and more evenly. The result is denser vapour at a given wattage compared with a standard round-wire coil.
• Quicker ramp-up: mesh warms rapidly, which is why firing feels instant.
• Consistent flavour: there are fewer cold or burnt spots, so flavour stays steady across the coil's life.
• Efficient wicking: the cotton touching the mesh feeds fresh liquid across the whole surface, which helps resist dry hits when you vape within the rated wattage.

Resistance is measured in ohms, and sub-ohm means below 1.0 ohm. Lower resistance draws more current at a given voltage, which gives more power and bigger vapour. A coil in the 0.15 ohm range is built for high wattage, 0.2 ohm is a flexible all-rounder, and 0.3 to 0.4 ohm coils suit lower, cooler settings and tend to be gentler on the batteries. Each coil prints its recommended wattage range on the side, and you should stay inside it. Starting at the low end of the range and moving up in 5W steps is a sound way to find your setting.

Fitting a new coil is straightforward. Unscrew the base of the tank, remove the old coil, screw in the new one finger-tight and refit the base. Then prime it: drip a few drops of e-liquid directly into the cotton openings and the coil's side holes, fill the tank, and wait five to ten minutes before the first puff. Skipping this step is the most common way to burn a new coil within its first day.

Coil life varies with use. Expect roughly one to three weeks from a coil at moderate settings with typical liquids. Sweet liquids, high wattage and chain vaping all shorten it. Signs that it is ready for replacement include a burnt or flat taste, gurgling, reduced vapour and a dark, sticky look to the cotton. Replacement coils usually come in packs of five or so, which reduces the per-coil cost, so buying a pack with the kit avoids being caught short.

One compatibility note: always buy coils that are specifically listed for this tank. Coils from other Vaporesso ranges can look similar but are not interchangeable, and a poor fit causes leaks or electrical faults.

Choosing a nicotine strength

The Armour Max ships with no e-liquid, so you choose your nicotine strength through the liquid you buy. This matters more on a high-power kit than on a pod, because big sub-ohm puffs carry more nicotine with every inhale. In the UK, nicotine e-liquid is capped at 20mg/ml and is sold in bottles of 10ml or less. The same 20mg/ml limit applied to disposable vapes before they were banned, and it still applies to pods and refill liquids. Nicotine-free liquid, called shortfill, comes in larger bottles with space to add nicotine shots.

Direct-lung vaping at sub-ohm power generally calls for much lower strengths than mouth-to-lung devices. Large puffs deliver a lot of vapour, and strong liquid in such volumes quickly becomes harsh. As a starting point:

• 0mg: for those who have quit nicotine or are finishing a step-down plan. Flavour only.
• 3mg: a common starting point for light-to-moderate smokers moving to sub-ohm. Smooth at 50 to 70W.
• 6mg: for people who smoked heavily and still want a firm throat hit. Works best at the lower end of the power range with a 50VG/50PG liquid.
• 9 to 12mg: only for very heavy smokers, and only with 50VG/50PG liquids at low wattage. Above this the vapour is usually too harsh in a big sub-ohm tank.

Avoid strong nicotine salts at high wattage. Salt liquids at 10 to 20mg/ml are designed for small pods with restricted airflow. Used in a high-powered tank they are harsh on the throat and can deliver far more nicotine than you intend. If you like a salt-style hit, drop the wattage, use a coil in the 0.3 to 0.4 ohm band and keep puffs short.

To mix your own, put a 50ml shortfill into a 60ml bottle, add one 10ml 18mg nicotine shot, shake well and you have 60ml at roughly 3mg/ml. Always check the shot strength and bottle volume on the labels so you can work out the final figure. Let the bottle rest for a day if you can; the mix settles and tastes more rounded.

Whatever strength you choose, listen to your body. Dizziness, nausea or a racing heart point to too much nicotine, in which case stop, drink some water and go lower next time. If you are still reaching for cigarettes, nudge the strength up one step, for example from 3mg to 6mg, rather than raising the wattage. Stepping down gradually is the aim: many ex-smokers reduce their strength every few weeks as cravings fade.

Who the Armour Max suits, and who should skip it

Matching a device to the person using it avoids wasted money. Here is who tends to get on well with the Armour Max.

It suits:

• Existing vapers who have outgrown pod kits and want denser vapour, richer flavour or more control.
• Ex-smokers who found low-power devices unsatisfying and want a robust, higher-capacity system, provided they are comfortable with direct-lung inhalation.
• People who vape heavily through the day and prefer swapping cells over waiting for a built-in battery to charge.
• Anyone with a physically demanding job or active lifestyle who wants a tougher device.
• Tinkerers who want the option to experiment with other 510 tanks later.
• Adults who want a reusable, repairable alternative to single-use devices.

It is probably not for:

• Complete beginners who have never vaped. A simpler pod or a lower-power single-battery kit is a gentler start, with less to learn and less to go wrong.
• Anyone who wants a tight, cigarette-like mouth-to-lung draw. This is a direct-lung system, and forcing it into mouth-to-lung use with a high-power coil produces hot, wasteful vapour.
• People who want a pocket-sized, discreet device. This is a chunky kit.
• Those who dislike handling batteries. You need to buy, charge, inspect and eventually recycle 18650 cells.
• Anyone who vapes strictly with high-strength nicotine salts. Pod systems suit that better.
• Non-smokers and under-18s. Vaping is for adult smokers looking for an alternative; if you do not smoke, there is no reason to start.

A useful rule of thumb: if you currently use a pod and are happy, there is no urgency to switch. If you use a pod and keep turning it up, or find the flavour thin, the Armour Max is a logical next step.

It is also worth being realistic about the learning curve. Expect an hour or two of adjusting wattage, airflow and liquid before it feels right. That is normal for any sub-ohm kit, and the reward is a setup tuned to your own preferences rather than a fixed factory profile.

Setting up and using the kit

Setting up takes only a few minutes. Follow these steps in order.

• 1. Unpack and inspect. Check that the mod, tank, coil, USB-C cable and spare parts are present. Remove any protective film from the glass and screen, and make sure the O-rings are seated.
• 2. Install the coil. Screw the supplied coil into the tank base finger-tight. If the kit ships with a coil pre-fitted, still check that it is snug.
• 3. Prime the coil. Add a few drops of e-liquid into the cotton through the coil's side holes.
• 4. Fill the tank. Open the top-fill cover, pour e-liquid in while avoiding the central tube, and close it again. Fill to just below the top and leave a little air space.
• 5. Wait. Leave it for five to ten minutes so the cotton fully soaks. This is the step that protects a fresh coil.
• 6. Insert the batteries. Check the polarity marks inside the battery bay, drop in both cells to match, and close the cover. Use a matched pair.
• 7. Attach the tank. Screw the tank onto the 510 connector until it is snug. Do not overtighten.
• 8. Switch on. Vaporesso devices normally switch on and off with five quick presses of the fire button, but confirm this in your printed manual. The screen shows the coil resistance and a wattage setting.
• 9. Set the power. Start at the bottom of the coil's recommended range and increase in 5W steps.
• 10. Adjust airflow. Open the airflow ring for cooler, bigger, airier draws, or close it partially for warmer, more flavour-rich vapour.

Take your first few puffs slowly. Inhale for three to five seconds with a gentle, steady pull rather than a gulp. Hold the fire button only while drawing, and release it when you stop inhaling.

Everyday care keeps the kit reliable. Refill before the tank is completely empty, since running dry is the quickest route to a burnt coil. Wipe the 510 connector and tank base occasionally with a dry cloth or cotton bud. Rinse the tank with warm water and let it dry fully when changing coils or flavours. Do not leave the device in a hot car or in direct sunlight, and keep it away from children and pets. Store spare cells in a case rather than loose in a bag.

Finally, lock the device when carrying it. Most regulated mods include a lock function, typically a set of rapid presses, which prevents accidental firing in a pocket or bag. Check the manual for the exact sequence.

Troubleshooting common problems

Most issues with a sub-ohm kit are simple to fix. Work through the likely cause before assuming the device is faulty.

• Device will not switch on or fire: check that both cells are the right way round and charged. Clean the battery contacts with a dry cloth. Try a different matched pair of cells to rule out a faulty one.
• Screen shows a coil or atomizer error: the mod cannot detect a coil. Check that the tank is screwed on firmly, the coil is seated and the 510 connector is clean. If the message persists, fit a new coil.
• Burnt or acrid taste: usually a dry or worn coil. Make sure the coil was primed and the tank is not running low, lower the wattage a little, and replace the coil if the taste persists after a refill.
• Weak vapour or muted flavour: the coil may be worn or gunked, particularly with sweet liquids. Confirm the airflow is not closed too far, then change the coil. Also check that the wattage is within the coil's range.
• Leaking from the tank or airflow: check the base is tightened, the O-rings are seated and not cracked, and the tank is not overfilled. Thin, low-VG liquid leaks more readily than thick liquid. Store the tank upright.
• Gurgling or spitting: too much condensation in the chimney or a flooded coil. Blow gently through the drip tip to clear it, wipe the tip and close the airflow slightly. If it continues, the coil may be flooding from an overfilled tank.
• Dry hits (hot, harsh puffs): the coil is not getting enough liquid. Refill, prime again, avoid chain vaping and avoid very thick liquids at high wattage.
• Batteries drain quickly: high wattage and sweet liquids both shorten run time, as do old cells. Cells that no longer hold their charge after a few hundred cycles should be recycled and replaced.
• Device gets hot: moderate warmth after heavy use is normal, but if the mod becomes uncomfortable to hold, stop using it. Once cool, remove the cells carefully and check them for damage.
• Charging problems: try another cable and power source, check the USB-C port for lint, and test the cells in an external charger. A cell that will not charge anywhere should be retired.

If a problem is not solved by these steps, stop using the device and contact the retailer with your order number and a description of the issue. Do not attempt to open the mod, and do not use any cell that shows damage. When in doubt, take the cells out.

Value for money and how it compares

Judging value means looking at total cost over time, not just the shelf price. The kit covers the mod, tank, a coil and basic accessories. On top of that you will need two 18650 cells (ideally plus an external charger and a carry case), a supply of e-liquid, and replacement coils every one to three weeks. Coils are usually sold in packs of five, so a single pack covers a couple of months for most people.

Against single-use devices, which have been banned from sale in the UK since June 2025, a refillable kit spreads its cost over months and years. A heavy vaper who once bought a couple of disposables each week typically comes out ahead within a month or two, because e-liquid and coils cost far less per day than a throwaway device. Against a basic pod kit, the Armour Max has a higher up-front cost and higher running costs if you vape at high wattage, but it gives you control over power, airflow and liquid, and its parts are replaceable rather than sealed in.

Where it delivers value:

• Tough construction that should survive daily carry and occasional drops.
• A wide power range, so the same device works at 35W or 85W as your habits change.
• Removable batteries, so you can swap a pair in seconds and replace them when they wear out rather than binning the whole device.
• A standard 510 connection that keeps future tank upgrades open.
• Coils and e-liquid that are widely stocked in UK shops.

Where it is weaker:

• Batteries and a charger are extra costs.
• The 2ml UK tank means frequent refills at high power.
• It is bulkier than most pod systems.
• No waterproof or dustproof rating is claimed.

How it compares with similar kits, fairly:

• Vaporesso GEN 200: a sibling from the same maker with a similar 220W-class dual-battery layout. The choice between the two mostly comes down to shape, grip, price and which coil range you prefer, so compare current prices and handle both if you can.
• GeekVape Aegis Legend 2: a dual-battery kit marketed with an IP67 rating for water, dust and shock resistance. For outdoor workers or anyone rough on their kit, that rating is a real advantage the Armour Max does not claim.
• Voopoo Drag series: a comparable dual-battery approach with its own coil family. Worth comparing on price, coil availability and how the grip feels in your hand.
• Pod kits such as the Vaporesso Xros range: smaller, simpler and gentler on nicotine, with a tighter draw. They are the better pick if you want something light and discreet, though you give up power and flavour depth.

The bottom line: the Armour Max is good value for a vaper who wants a durable, high-headroom direct-lung kit and is happy to manage removable batteries. If you want something small, simple and low-maintenance, a pod kit will serve you better, and if outright weather resistance is your priority, look at models that carry a formal rating.