Innokin Endura T 8E Vape Starter Kit 1

Overview

The Innokin Endura T 8E Vape Starter Kit 1 by Innokin in 1 at 0mg. Free UK delivery over £20, same-day dispatch on weekday orders before 4pm.

Innokin Endura T 8E Vape Starter Kit at a glance

The Innokin Endura T 8E Vape Starter Kit is a compact, refillable pen-style kit from Innokin, a Shenzhen manufacturer that has been making vaping hardware since 2011 and has built a loyal UK following for dependable, no-fuss starter devices. The Endura range exists to answer a simple question: what does someone need if they want to stop smoking, or just stop buying single-use devices, without learning coil building to do it? The answer is a small rechargeable battery, a tidy little tank, a pre-fitted coil and a mouth-to-lung draw that feels familiar if you have ever smoked a cigarette.

This guide goes through the kit properly rather than repeating a spec sheet. We cover how the Endura T 8E performs day to day, what flavour to expect, how the battery behaves, what the coil and tank design means for your choice of e-liquid, which nicotine strength to pick, and where the kit falls short. We also compare it honestly with the other starter kits you are likely to be weighing up, because for some vapers the right answer will be a different device.

A quick note on naming and specs. The listing calls this the Endura T 8E, and it sits in the same pocket-sized refillable family as Innokin's other Endura T-series kits. Where we quote numbers below, we use typical figures for that class of device and we flag anything you should confirm against the printed box or manual in your parcel. Manufacturers revise small details between batches, and we would rather be accurate than impressive.

The key points in short:

• Refillable starter kit, so you buy e-liquid in bottles instead of binning a whole device when it runs dry
• Mouth-to-lung (MTL) style draw, suited to nicotine salts and standard freebase liquids at modest power
• Small tank sized for the UK limit of 2ml per tank
• Rechargeable built-in battery, topped up by cable
• Replaceable coils, so one kit lasts for months rather than days

What you get in the box and the specs that matter

A starter kit is only useful if it arrives with everything you need to be vaping the same evening. The Endura T 8E kit is built around that idea. Inside the box you should find the battery body, the tank with a coil already installed, a charging cable, a spare coil or sealed coil pack depending on the batch, a short manual and the usual warning and compliance leaflet. You will need to supply your own e-liquid, which is a deliberate choice: it lets you pick the flavour and strength rather than being locked to whatever the manufacturer sells.

Here are the specifications that actually affect how you will use it. Treat these as the typical figures for the Endura T-series class and check them against your box:

• Device type: refillable MTL pen-style starter kit
• Battery: built-in rechargeable cell, typically around 1000mAh in this class
• Output: fixed, low-teens wattage, tuned to the supplied coils
• Tank capacity: 2ml, in line with the UK maximum for refillable tanks
• Coil resistance: Prism-series coils at roughly 1.5 to 1.8 ohm
• Intended liquid: 50/50 or similar PG/VG balance, including nicotine salts
• Charging: by cable, with a full charge normally taking around an hour or so

None of those numbers are exciting, and that is the point. A device in this category is meant to be predictable. There are no menus to learn, no wattage dial to get wrong and no temperature modes to puzzle over. You fill it, wait a few minutes, and vape it. If you have used a larger variable-wattage device before, the lack of adjustment may feel limiting. If you are coming from cigarettes, it is usually a relief.

One practical tip about the box contents: keep the manual and the coil packaging for the first month. The coil packaging shows the resistance and recommended power range printed on it, which is the quickest way to confirm you are buying the right replacements later.

Performance and vapour delivery

The Endura T 8E is a mouth-to-lung device, which means you draw the vapour into your mouth first, pause briefly, then inhale. This is the same rhythm as drawing on a cigarette, and it is the main reason kits like this are recommended to people who are switching. The airflow is deliberately restricted, so the vapour comes through at a measured pace and the throat sensation is firm without being harsh at sensible nicotine strengths.

In practical terms, expect the following from a device of this type. Vapour production is modest, well short of the clouds you see from sub-ohm kits, but it is entirely sufficient for MTL vaping. Throat hit is the main sensation, particularly with freebase nicotine. With nicotine salts the hit is smoother and the nicotine is delivered more quickly, which many ex-smokers find more satisfying at lower strengths.

Warm-up is quick. With a freshly primed coil, the first draw after a refill should produce flavour within a second or so. If the first few draws taste thin or slightly dry, the coil is still saturating, which we cover in the troubleshooting section.

Where the kit performs best:

• Short, frequent puffs throughout the day, the pattern most smokers already have
• Standard 50/50 e-liquid and nicotine salts at 10mg to 20mg
• Moderate ambient temperatures and a coil that has been properly primed

Where it is less comfortable:

• Long, deep, cloud-style draws, because the airflow is not designed for them
• Very thick, VG-heavy liquids, which can wick slowly on a coil this size
• Constant chain vaping, which can outpace both the wicking and the 2ml tank

If you try to vape it like a sub-ohm device, you will be disappointed and the coil will wear out faster. Used the way it was designed, it is a steady, unfussy performer. Many people who start on a kit like this stay with it for months because it simply keeps working.

Flavour profile and what to expect from your e-liquid

The Endura T 8E does not have a flavour of its own, since it is a refillable kit, but the hardware shapes how your chosen liquid tastes. Restricted MTL airflow and a small coil tend to produce a tight, concentrated flavour rather than a diffuse, airy one. Tobacco, menthol, fruit and dessert profiles all come through clearly, and the tighter draw tends to favour flavours that are well defined rather than ones that rely on large volumes of vapour to make their point.

Here is a rough guide to what tends to work well:

• Tobacco and tobacco blends: a natural fit for MTL, and the usual starting point for people switching from cigarettes
• Menthol and mint: crisp and clean in a small coil, with the cooling effect noticeable even at lower strengths
• Fruit and ice: bright and clear, and probably the most popular category among UK vapers
• Bakery, custard and dessert: workable, but sweeter liquids can leave residue on the coil sooner, so expect to change coils a little more often

A word on coil life and flavour. Sweetener-heavy liquids caramelise on the coil surface over time, which dulls the taste and eventually gives a burnt note. You can slow this down by taking gaps between puffs, not chain vaping, and keeping the tank above a quarter full so the wick stays wet. If a flavour that used to taste vivid starts to taste flat or muddy, the coil is almost always the cause, not the liquid.

Changing flavours is straightforward, but it is not instant. Residue from the previous liquid stays in the coil, so ghost notes can linger for a few draws. If you change between very different profiles, such as a heavy dessert to a clean menthol, a fresh coil gives the cleanest result. Some vapers keep a dedicated coil for menthol for exactly this reason.

Finally, remember that new liquids benefit from a little time. Many fruit and dessert liquids taste better after a few days of steeping in a cool, dark place, so a bottle that seems a bit sharp on day one may settle nicely.

Design and build quality

Innokin has a reputation for sensible, durable industrial design rather than flashy styling, and the Endura T 8E follows that approach. The body is a compact pen-style shape that fits in a jacket pocket or the small pocket of a pair of jeans without a visible bulge. It is light enough that you stop noticing it, and the slim profile makes it easy to hold between fingers in a way that feels close to a cigarette.

Build quality in this class is generally good for the price. The battery body is a rigid, well-finished shell, the threading between the tank and battery should engage smoothly, and the drip tip fits snugly without wobble. You would not describe it as premium, since you are not paying for premium, but nothing about it feels flimsy.

A few design details are worth knowing:

• Tank construction: a compact tank with a clear section so you can see the liquid level at a glance
• Filling method: designed to be refilled through a fill port, so you do not need to take the tank apart for every top-up
• Drip tip: a standard, comfortable mouthpiece. If you dislike it, many MTL drip tips in common sizes can be swapped in, though you should check fit first
• Finish: a durable coating that handles pocket wear, though keys and loose change will scuff any finish eventually

One honest observation: the small size is both the strength and the limitation. The tank is small, the battery is small, and everything else is small, which means the kit trades capacity for convenience. If you value portability above all else, that is exactly the right trade. If you want one device to last an entire long day without a top-up, you will find yourself refilling and charging more often than with a larger kit.

Treat it sensibly. Avoid leaving it in a hot car, keep it away from liquids around the charging port, and do not carry it loose with a full tank in a bag where the button can be pressed. These habits cost nothing and extend the life of any small vape device.

Battery life and charging

A built-in battery of around 1000mAh, typical for this class, is well matched to a low-power MTL device. Because the output is modest, the battery goes a long way: many users get a full day of ordinary use from a single charge, and lighter users may stretch it to a day and a half. Heavy chain vapers will want to top up during the day.

Real-world battery life depends on four things:

• How often you vape: frequent short puffs use more energy than a handful of longer sessions
• Puff length: shorter draws on a low-power device add up to significantly less drain
• Ambient temperature: cold weather reduces effective capacity in every lithium cell, so expect a little less in winter
• Coil condition: a worn or gunked coil draws more effort from the battery for less result

Charging is by cable, and the sensible approach is to charge with a standard 5V phone-style charger or a computer USB port rather than a very high-output fast charger. Most devices of this kind have built-in protection circuits, but gentle charging is kinder to the cell in the long run. Plan on around an hour for a full charge, and avoid leaving the device on charge unattended overnight on a soft surface such as a bed or sofa.

Good battery habits:

• Top up when it gets low rather than running it completely flat every time
• Use the cable supplied, or a quality replacement, since cheap cables can fail or charge slowly
• Never use the device if it is swollen, damaged or unusually hot
• Keep it dry, and keep the charging contact clean

Because the battery is built in, it cannot be swapped out like the cells in a mod. Over a couple of years of daily use the capacity will fade gradually, as it does in any phone or tablet. When it no longer gives you a workable day, that is the time to replace the kit rather than the battery.

At the end of its life, do not put the device in household waste. Lithium batteries can start fires in bin lorries and recycling plants. Take it to a household waste recycling centre, or to a retailer drop-off point for small electricals and batteries, which most large UK supermarkets and electrical shops provide.

Coil and tank technology explained

The part of the kit that does the real work is the coil, and understanding it will save you money. The Endura T 8E uses replaceable Prism-series coils, which are a plug-in cartridge style: a small cylinder containing a heating element wrapped around or through a cotton wick, sitting inside a metal housing that screws or pushes into the tank. You do not build or wrap anything. When the coil wears out, you pull it out and fit a new one in about thirty seconds.

The resistance of the supplied coil is in the region of 1.5 to 1.8 ohm. In plain terms, higher resistance means lower power draw and a cooler, tighter vape. That is precisely what you want for MTL, and it is why this kit pairs well with nicotine salts and with standard 50/50 e-liquids. Low-resistance coils intended for sub-ohm vaping use far more power and would not suit the airflow of this tank.

How the coil works, step by step:

• E-liquid soaks into the cotton wick from the tank through small wicking holes
• Pressing the fire button or inhaling, depending on how your unit activates, sends current through the heating wire
• The wire heats the saturated wick and the liquid vaporises
• The vapour passes up the centre of the coil and out through the drip tip

Coil life is not fixed, because it depends on the liquid you use, how often you vape and how well you look after it. As a rough guide, many UK vapers replace the coil every one to two weeks of regular use. Sweeter liquids shorten this, and clean, thin liquids lengthen it. The clear signs of a coil that needs replacing are a burnt or flat taste, reduced vapour, a gurgling sound, or leaking.

Always buy the correct replacement coil for this device. Mismatched or unbranded coils can fit loosely, leak or perform poorly, and a coil of the wrong resistance can overheat or give weak output. Write down the series printed on your coil packaging so you can match it later.

The tank itself is a simple design with a 2ml capacity. That small volume is not a flaw; it reflects the UK rule that refillable tanks must not exceed 2ml. It does mean you will refill more frequently than you would on a larger tank elsewhere in the world, but the 10ml bottle cap on nicotine e-liquid makes frequent topping up a normal part of UK vaping anyway.

Choosing the right nicotine strength

Nicotine strength is the single most important choice you make with this kit, and getting it wrong is the most common reason new vapers give up. In the UK, e-liquid sold for refillable devices is capped at 20mg/ml of nicotine, and bottles of nicotine liquid are capped at 10ml. The 20mg limit applies across the board, and it is the same ceiling that applies to single-use vapes, so you are never buying something stronger by switching to a refillable kit. What you choose within that range matters, though.

For an MTL device like the Endura T 8E, these starting points are widely used:

• Heavy smokers (20 or more cigarettes a day): nicotine salt at 18mg to 20mg, or freebase at 12mg to 18mg
• Moderate smokers (10 to 20 a day): nicotine salt at 10mg to 18mg, or freebase at 9mg to 12mg
• Light smokers or social smokers: nicotine salt at 10mg, or freebase at 3mg to 6mg
• Ex-smokers stepping down: reduce gradually, for example from 18mg to 12mg to 6mg, giving yourself a few weeks at each step

Salts versus freebase is the other big decision. Nicotine salts deliver nicotine quickly and with a smoother throat feel, which is why they are popular for low-power kits like this one. They are normally sold at 10mg and 20mg, and 20mg salts feel noticeably gentler than 20mg freebase would. Freebase nicotine gives a sharper throat hit, is traditionally sold in lower strengths, and suits people who like that crisp feel.

Signs you have the strength wrong:

• Too low: constant puffing, cravings returning within the hour, or a feeling that vaping is not satisfying
• Too high: dizziness, nausea, a harsh throat hit that is unpleasant, or a racing heartbeat

If you feel any of the second group, stop, drink some water, and drop to a lower strength next time. Start where you think you need to be, not where a friend recommends, because everyone's tolerance differs. Nicotine is addictive, and vaping is intended for adult smokers who want to move away from cigarettes, not for non-smokers or anyone under 18. If you are pregnant or have a medical condition, speak to your GP or a local stop-smoking service first.

Who the Endura T 8E is for, and who should look elsewhere

Every vape kit is a compromise, and being honest about who a device suits saves you money. The Endura T 8E is aimed squarely at adult smokers and recent switchers who want something that works without fuss. If any of the following sound like you, it is worth serious consideration:

• You are replacing cigarettes and want a draw that feels familiar
• You are tired of paying for single-use devices and want to move to something refillable
• You want a small, pocketable device with no adjustments to learn
• You use nicotine salts or standard 50/50 e-liquids
• You want a low-cost way to try refillable vaping before committing to a larger setup

It is less suitable if:

• You want big clouds or a loose, airy draw, in which case a sub-ohm kit or a larger device is a better fit
• You vape very heavily and dislike refilling a 2ml tank frequently
• You enjoy tinkering with wattage, airflow and rebuildable coils
• You use thick, high-VG e-liquids as your standard choice

The kit also suits people moving from single-use vapes. UK rules now prohibit the sale of single-use vapes, and a refillable kit like this is the natural next step. It gives you a similar convenience, a better range of flavours and strengths, and a much lower cost per day once you are set up. If you have been used to a 600-puff single-use device, this will feel familiar in size and effort, with the added task of refilling and the occasional coil swap.

It is not suitable for anyone under 18, and it should not be used by non-smokers. Vaping is a harm-reduction tool for adult smokers, not a lifestyle accessory, and we are required to verify age on order. Keep the device, e-liquid and spare coils well out of reach of children and pets.

How to use the kit: first fill, priming and daily use

Setting up takes about ten minutes, and doing it properly on day one avoids the most common problems. Follow these steps:

• Charge first. Plug in the device and charge it fully before first use, following the indicator light guidance in the manual.
• Inspect the coil. Make sure the coil is fully seated in the tank. If the tank arrived with a coil fitted, check it sits snugly.
• Prime the coil. Place a few drops of e-liquid directly onto the exposed cotton through the wicking holes. This stops a dry hit on the first draw.
• Fill the tank. Open the fill port and add e-liquid, aiming the bottle nozzle at the side of the opening so you do not flood the centre airflow tube. Do not overfill.
• Wait. Leave the tank to stand for five to ten minutes so the cotton soaks fully.
• Close, attach and vape. Screw the tank onto the battery, then take gentle, short puffs first.

Daily use is simple. Take a slow draw of two to four seconds, hold it in your mouth for a moment, then inhale. Pause for ten to thirty seconds between puffs to let the wick re-saturate. Chain vaping dries the wick quickly and shortens coil life.

Good habits that keep it working:

• Top up before the tank gets close to empty
• Store the device upright when you can, to reduce leaks
• Wipe the connection and drip tip with a dry tissue occasionally
• Rinse the tank with warm water when you change coils or flavours, and let it dry fully before refilling

Changing a coil is just as easy. Unscrew the tank from the battery, empty any remaining liquid, pull out the old coil, push in the new one until seated, prime it with a few drops, refill, and leave it to stand. Dispose of used coils with small electricals where your local council allows, or ask at a recycling centre, since they contain metal.

If you use the device with a fire button, the standard five-click on and off convention is common on this class of kit, but check your manual for the exact behaviour of your unit.

Troubleshooting common problems

Nearly every issue with a small refillable kit comes down to the coil, the liquid level or the connection. Before you assume the device is faulty, run through these checks.

Burnt or dry taste. This usually means the coil is running dry or has worn out. Check the tank is not nearly empty, prime the coil again with a few drops and wait, then try shorter puffs with longer gaps. If it persists, fit a new coil.

Weak or no vapour. Check the battery charge, confirm the tank is screwed on firmly, and make sure the coil is seated. A coil clogged with sweet residue will also produce thin vapour, and replacing it is the quickest fix.

Leaking. Common causes include overfilling, a loose coil, a damaged seal or travelling on a plane or on a hill, where pressure changes push liquid out. Check the coil is pressed in fully, do not overfill, and store the device upright. Wipe the outside and the battery connection dry before use.

Gurgling noise. This usually means excess liquid has reached the airflow path. Blow gently through the drip tip with the device off, wipe it clean, and be a little more careful when refilling.

Flashing lights or a device that will not fire. Often a sign of a poor connection, a low battery or a short-circuit protection trigger. Clean the contact points, reseat the tank and recharge. Consult the manual for what the indicator colours mean on your unit.

Will not charge. Try a different cable and a different power source. Check the port for lint and dust, and clean it gently with a dry wooden toothpick, never metal, with the device off.

Hot device. If the device becomes unusually hot, stop using it, let it cool, and do not charge it. If it is swollen or damaged, stop using it altogether and contact us.

If you have worked through these checks and the device still misbehaves, contact us with your order number and a short description. Faulty kits are dealt with under your statutory rights, which we explain in the FAQs.

Value for money and how it compares with similar starter kits

The cost of a kit like this has two parts: the upfront price and the running cost. The upfront price is modest, and the running cost is where refillable vaping beats single-use. A 10ml bottle of e-liquid typically costs a few pounds and lasts a regular MTL vaper several days. Coils are the other ongoing expense, and at one every one to two weeks, the monthly cost of keeping the Endura T 8E running is usually well below what a pack-a-day smoker pays for cigarettes in the UK, and comfortably below the cost of using single-use devices daily.

To be fair about it, here is how the kit stacks up against typical alternatives:

• Versus pod kits with closed cartridges: sealed-pod devices are even simpler, with no coil to prime, but you pay for the pod each time and your flavour choice is limited to what the manufacturer sells. The Endura gives you the freedom to use any compatible e-liquid at a lower ongoing cost.
• Versus refillable pod kits from other brands: popular refillable pod kits such as those in the Vaporesso, Uwell and Smok ranges offer similar MTL performance. Some have larger batteries or adjustable airflow, which can suit you better if you want tuning options. The Endura's advantages are straightforward operation and Innokin's well-established coil range.
• Versus sub-ohm starter kits: sub-ohm kits produce far more vapour and flavour volume, but they use much more e-liquid, drain faster and suit lower nicotine strengths only. They are a different style of vaping rather than a better one.
• Versus single-use devices: single-use vapes are no longer sold in the UK, and they were always poor value over time. A refillable kit is greener, cheaper to run and offers many more flavours.

Where the Endura T 8E is weaker than some rivals: the 2ml tank is small, the output is fixed, and the battery is built in rather than replaceable. If you want USB-C fast charging, adjustable airflow, or a screen showing battery and coil status, check the specs of other kits closely. You will often pay more for those features.

On balance, it offers sound value for adult smokers who want a dependable, low-fuss starter. It does the basics well, uses widely available coils, and is backed by a manufacturer with a long track record. For a first refillable kit it is a sensible, low-risk purchase.

When you are finished with the device, remember that it counts as waste electrical equipment. Use a household waste recycling centre or a retailer drop-off point for small electricals and batteries, and never put it in your general rubbish or standard recycling bin.