Lost Vape Orion Pod (Pack of 2) 0.25Ohm

Overview

The Lost Vape Orion Pod (Pack of 2) 0.25Ohm by Lost Vape in 0.25Ohm at 0mg. Free UK delivery over £20, same-day dispatch on weekday orders before 4pm.

Overview of the Lost Vape Orion Pod 0.25 Ohm (Pack of 2)

This listing is for a twin pack of replacement pods from the Lost Vape Orion range, each fitted with a 0.25 ohm coil. It is an accessory rather than a complete kit, so you need an existing, compatible Orion device to use it. Lost Vape built its reputation on well-finished hardware, and the Orion line is its refillable pod platform, where the e-liquid reservoir and the coil are one sealed, replaceable unit. When the coil wears out you replace the whole pod instead of rebuilding anything or swapping a loose coil head.

The 0.25 ohm figure is the headline detail. Most pod systems that UK vapers come across sit between roughly 0.6 and 1.2 ohm, which suits a tight mouth-to-lung draw similar to a cigarette. A 0.25 ohm coil is at the opposite end of the scale. Lower resistance lets more current pass through the coil at any given voltage, so it heats quickly, makes noticeably more vapour and runs warmer, and it needs a looser, more open draw to be comfortable. In practical terms this is a pod for loose mouth-to-lung or direct-to-lung inhaling, and it suits e-liquids with a higher proportion of vegetable glycerine (VG).

What the pack contains:

• Two refillable pods, each with an integrated 0.25 ohm coil
• A user-fill design, so you add your own nicotine e-liquid or a nicotine-free shortfill blend
• No battery, no charger and no e-liquid, because these come from your device and your own liquid purchase

Pods like this are also a more sensible long-term route than single-use hardware. Since the ban on single-use vapes came into force across most of the UK in June 2025, refillable systems have become the mainstream choice, and a pack of two pods lasts considerably longer, and creates far less waste, than a drawer full of throwaway devices. This page covers how the pod behaves, who it is for and where it falls short, so you can decide before you order.

Compatibility and what is in the pack

Compatibility is the single most important thing to check with any pod accessory, and it is the most common cause of returns across the whole category. Lost Vape has released several different devices under the Orion name and its sub-ranges over the years, and the pods from different generations are not universally interchangeable. The pod body, the contact pins, the airflow path and the retaining lugs can all differ from one generation to the next, even when the name on the box looks similar.

Before ordering, work through this short check:

• Identify your exact device model from the label on the base or the original box, not just the word Orion
• Compare the shape and connection end of your current pod against the product photos on this page
• Check your device's recommended resistance and wattage range, because a 0.25 ohm coil needs a device able to deliver enough power safely
• If your current pods have a resistance printed on the side, confirm which ranges your device supports

The resistance check deserves a second look. A 0.25 ohm coil draws far more current than a 0.8 ohm coil at the same wattage. As a worked example, at 20W a 0.25 ohm coil runs at about 2.2V and pulls close to 9A, whereas a 0.8 ohm coil at the same wattage runs at about 4V and pulls around 5A. Devices that detect coil resistance automatically will usually either adjust their output or refuse to fire if the coil falls outside their design range. If your device is fixed-output and designed around higher-resistance pods, fitting a 0.25 ohm pod could produce weak performance, error messages or excessive strain on the battery.

If you are unsure, the safest approach is to contact us with your device model before buying. Matching the pod to the device correctly protects your battery, gives you the vaping experience Lost Vape intended and saves the hassle of sending an unopened pack back. Because a pod touches e-liquid as soon as it is filled, please do not fill or fire one until you are certain it seats properly in your device.

Performance and puff delivery

Performance is where a 0.25 ohm coil separates itself from the usual 0.6 to 1.0 ohm pods. With enough power behind it, the coil heats in a fraction of a second, so the first moment of each draw is already producing vapour, and there is little of the lag you notice with higher-resistance coils. Vapour production is substantial for a pod format, and the throat sensation is warmer and rounder than the cool, tight pull of a mouth-to-lung pod.

It helps to be clear about puff counts. A pod has no fixed puff count the way a disposable does, because the number depends entirely on how you vape. As a rough, honest estimate, a low-resistance coil running at around 15 to 25W with three-second draws uses somewhere between 0.01 and 0.025 ml of liquid per puff. On a 2 ml fill that works out to roughly 80 to 200 puffs before you need to top up, and nearer the lower figure if you run the device at the top of its range. That is far fewer than the 600 or 800 puffs printed on many single-use devices, so expect to refill often. The trade-off is that each puff is considerably denser.

• Warm-up: fast, because the low resistance heats the coil quickly at modest voltage
• Vapour volume: high for a pod, comparable to a small sub-ohm tank on a low setting
• Draw style: open and airy, intended for loose mouth-to-lung or direct-to-lung inhaling
• E-liquid consumption: high, so plan on refilling more than once a day if you vape steadily

What you fill the pod with matters. Liquids in the 50/50 to 70/30 VG to PG range usually wick well through the small cotton ports of a pod coil. Very thick, high-VG blends (80VG and above) can struggle to feed the coil fast enough at 0.25 ohm, which leads to dry or scorched-tasting hits. Heavily sweetened dessert liquids can also leave residue on the coil faster than lighter fruit or menthol blends, shortening the working life of the pod.

Realistically, treat the pod as a performance part rather than an economy part. You are paying for warm, dense vapour and quick response, and in return you accept a shorter coil life and a higher refill rate than a 1.0 ohm pod would demand.

Flavour profile

A pod does not have a flavour of its own, because the e-liquid does. What the pod changes is how that flavour is delivered. A 0.25 ohm coil runs hotter and covers a larger area of cotton than a tight, high-resistance coil, which tends to give a fuller, warmer and rounder flavour. Sweet, creamy and bakery-style profiles, rich fruit blends and cola or custard flavours usually show their depth well here, and the heat helps those flavours register as part of a thick cloud rather than a thin, sharp hit.

Where low-resistance coils are less flattering is with delicate flavours. Light, crisp profiles such as cucumber, subtle mint or fine tea can taste muted or flattened at higher power, because the heat and airflow wash out the top notes. Menthol and ice blends become less icy when the vapour is warmer, so if cool vapour is what you want, choose a liquid with a stronger cooling agent or run the device at the lower end of its wattage range.

• Fruit and dessert profiles: generally work well, with a fuller body
• Tobacco and nutty blends: gain a smoother, deeper character but can taste toasted at high power
• Menthol and ice: lose some chill as the vapour warms, so pick stronger cooling profiles
• Delicate or floral flavours: may be muted, and are usually better in a higher-resistance pod

Coil break-in plays a part too. The first few draws of a new pod can taste slightly of cotton, or of very little, while the wick settles. Once the cotton is properly saturated, the flavour usually evens out after a few puffs. Switching between very different flavours in the same pod is where problems appear, because residue left on the wick and coil causes ghosting, so a berry liquid may carry traces of the menthol that went before it. The simplest habit is to dedicate one pod to one flavour and replace it before switching. With a pack of two, you can keep two flavours on the go and rotate them without cross-contamination.

Finally, remember that flavour is an early warning of coil health. When a liquid that tasted good starts to taste flat, slightly bitter or faintly burnt, the coil is on its way out, and no amount of topping up will bring it back.

Design and build quality

The Orion pod is a self-contained cartridge: a pod body that holds the e-liquid, an integrated drip tip you inhale from, a sealed coil at the base and electrical contacts that connect to the device. It is designed to be pushed or clipped into place, depending on the device generation, and removed in a few seconds. There are no threads to screw, no loose coil heads to handle and no tools needed, which is a large part of the appeal of pod vaping.

Lost Vape has a reasonable reputation among UK vapers for fit and finish, and pods in this family are generally a snug, positive fit rather than a loose rattle. Several details are worth checking when yours arrives:

• The seal between pod and device, where a loose or twisted pod can cause leaks or a no-fire message
• The fill port, which should be covered by a firm silicone bung that sits flush after filling
• The airflow opening, which should be clear and free of packing material
• The contacts at the base, which should be clean and undamaged
• The pod body, which should be free of cracks or clouding around the fill port and base

Be realistic about the materials. Pod bodies are plastic, and plastic can craze or crack over time when exposed to some flavourings and additives, particularly certain strongly flavoured, cooling or dessert-style liquids. If you see small cracks forming around the fill port or the base, replace the pod rather than carrying on, because a cracked pod leaks onto the device contacts and can eventually damage them. Many pods include a clear section so you can see the liquid level, which is useful with a coil that uses liquid quickly. Check the product photos for the exact window design on this model.

The pod adds very little bulk to the device, so pocketability depends almost entirely on the Orion device you pair it with. Capacity is also where UK rules come in: refillable pods and tanks sold for use with nicotine e-liquid are limited to 2 ml, so you should expect a fill capacity at or just under that figure and check the markings on the pod body. A 2 ml limit is one reason a thirsty 0.25 ohm coil needs frequent refills, and why a spare pod, which this two-pack provides, is a practical thing to carry.

Battery and charging considerations

The first point to make is that the pod has no battery, so there is nothing to charge in the pod itself. Battery life is a function of your Orion device, and the 0.25 ohm coil affects it more than most coils do. Lower resistance draws higher current for the same wattage, and the device battery has to work harder to supply it.

A simple illustration helps. At 20W, a 0.25 ohm coil draws roughly 9A and runs at about 2.2V. If your device has a battery in the region of 800mAh, the stored energy is about 2.9Wh, or roughly 10,500 joules. Each three-second puff at 20W takes about 60 joules, so even before allowing for losses a full battery covers fewer than 180 puffs, and in practice closer to 130 to 150. That is about the volume of one pod fill, so a full charge and a full 2 ml pod tend to run out at about the same time. It also means a device with a larger battery will serve this pod better, and a very small one will feel as though it lives on the charger.

Sensible charging habits protect both the battery and your home:

• Use the cable supplied with your device, connected to a standard 5V adapter or a computer port, and avoid unbranded high-output chargers
• Never leave a device charging unattended, or on a bed, sofa or other soft surface
• Stop charging and stop using the device if it becomes unusually hot, swells or smells odd
• Do not carry the device loose in a pocket or bag with keys or coins, which can short the battery
• Top up before the battery is completely flat, because partial charges are fine for lithium cells

Disposal matters too. When a device battery reaches the end of its life, or a pod is spent, do not put it in household rubbish or kerbside recycling. Lithium batteries start fires in bin lorries and recycling plants, and the number of these incidents in the UK has risen sharply as vape waste has increased. Shops that sell vapes are expected to offer take-back for waste electrical items, and many have a dedicated vape-recycling bin, as do many council household waste recycling centres. Your local council website lists the nearest drop-off point.

Coil and mesh technology

The coil is the heart of any pod, and in the Orion pod it is built in, so you never handle it directly. At 0.25 ohm it is a low-resistance design. Coils at this resistance usually reach that figure through one of two routes: a mesh element, which is a flat, perforated strip of resistance metal with a large surface area, or a wire element built with multiple strands or in parallel to bring the total resistance down. Lost Vape does not always print the coil material prominently on retail packaging, so check the pod label or the manufacturer's information if the exact material matters to you.

• Mesh: spreads heat across a wide surface, which generally means faster ramp-up, even flavour and fewer hot spots on the wick
• Wire: simpler construction that tends to give a crisper flavour with a more focused heat
• Either way: the element sits against organic cotton, which draws e-liquid in through the pod's wicking ports and feeds the coil as you inhale

Resistance sets how much power the coil needs and how the device behaves. A 0.25 ohm coil wants a device that can supply high current without the voltage sagging. Typical power for coils at this resistance falls somewhere in the mid-teens to mid-twenties of watts, but always follow the figure printed on the pod or in the device manual, because running a coil above its rated wattage burns the cotton and shortens its life dramatically. More power does not mean better vaping. It usually means a hotter, harsher and shorter-lived coil.

Coil wear comes from three main sources: gunk building up on the element from caramelised sweeteners and flavourings, cotton that dries out between refills, and repeated dry firing. With typical liquids and regular use, a pod at this resistance often lasts about one to two weeks, and less with sweet, thick liquids. A pack of two therefore covers a few weeks for most people. Because the coil is sealed in, it cannot be cleaned or rebuilt in any meaningful way, so the practical way to extend its life is to prime it properly, keep the pod topped up, take shorter puffs with pauses between them and avoid chain vaping at the top of the wattage range. When the flavour goes flat or burnt despite a fresh fill, replace the pod.

Nicotine strength guidance

Nicotine choice is more important with a 0.25 ohm pod than with most other coils, because each puff delivers more vapour, and so more nicotine, than a tight mouth-to-lung pod would. UK law caps nicotine e-liquid at 20mg/ml, the same ceiling that applied to the single-use devices now banned from sale, and bottles of nicotine e-liquid are limited to 10 ml. That ceiling is a maximum, not a recommendation. At the power levels a 0.25 ohm coil runs at, a 20mg/ml nicotine salt liquid will usually feel harsh in the throat and deliver more nicotine per puff than most people want.

As a general guide for adult smokers switching to vaping:

• 0 to 3mg/ml (freebase shortfill): light users, former smokers who have been vaping for a while, and anyone who vapes frequently through the day
• 3 to 6mg/ml (freebase): a common range for loose mouth-to-lung and direct-to-lung vaping, and suitable for moderate smokers moving over
• 10 to 12mg/ml (nic salt): for heavier smokers who need more nicotine but still want a manageable throat hit, and the upper limit many people find comfortable at this resistance
• 18 to 20mg/ml (nic salt): generally better suited to higher-resistance, low-wattage pods, and at 0.25 ohm it is likely to be harsh, wasteful and a lot of nicotine in one go

If you buy 0mg shortfill liquid, which is sold in larger bottles with space left for nicotine, you add nicotine shots to reach your chosen strength. For example, one 10 ml shot of 18mg/ml nicotine added to a 50 ml shortfill in a 60 ml bottle gives approximately 3mg/ml. The labelling on the shot and the shortfill will tell you the final mix, and shaking the bottle well after adding the shot makes sure the nicotine is evenly distributed.

A practical approach is to start lower than you think you need. If you find yourself chain vaping or topping up constantly to chase satisfaction, move up one strength step rather than increasing the power, since extra wattage mainly burns through liquid and coils. Vaping is intended for adult smokers looking to switch. Non-smokers and anyone under 18 should not use nicotine products, and nicotine is addictive. If you are pregnant, have a heart condition or take regular medication, speak to your GP or a local stop smoking service before using nicotine products.

Who the 0.25 ohm Orion pod is for

The 0.25 ohm Orion pod is a specific tool, so it suits a particular kind of vaper. It is worth being straightforward about both sides.

It is a good fit if you:

• Already own a compatible Orion device and want denser, warmer vapour than a standard-resistance pod gives
• Enjoy a looser, airier draw and prefer to inhale directly to the lungs or with a relaxed mouth-to-lung pull
• Use lower-strength e-liquid, in the 3 to 6mg/ml range, or a modest-strength nic salt
• Do not mind refilling more often and replacing pods more often in return for stronger vapour production
• Like to keep a couple of flavours rotating, which the pack of two lets you do

You should probably look elsewhere if you:

• Are new to vaping and want a cigarette-like, tight draw, where a 0.8 to 1.2 ohm pod is much easier to get on with
• Use high-strength nic salts (18 to 20mg/ml), which feel harsh and over-deliver at this resistance
• Want a device that lasts through a whole day on a single charge and a single fill without attention
• Need discreet vapour in shared spaces, since low resistance means bigger clouds
• Are not sure of your device model, because a mismatched pod is the most common problem with accessories like this

It is also worth being clear that vaping is for adults. You must be 18 or over to buy, and we may ask for age verification. If you do not currently smoke, there is no reason to start vaping.

For people who are switching from cigarettes, the usual advice is to find a set-up that is satisfying enough that you do not drift back to smoking. For some people that is a simple, tight-draw pod. For others who miss the warmth and volume of a cigarette, a lower-resistance pod like this one makes the switch easier to stick with. The right answer is personal, and it is reasonable to try one pack before deciding whether to stock up.

How to use the pod

Using the pod is straightforward, but doing the first fill properly makes the difference between a smooth pod and one that leaks or burns early. Follow these steps with a new pod.

• Check the fit. Confirm the pod matches your device before you open anything you cannot return.
• Remove packaging. Take off any protective film, plugs or caps from the drip tip and the base, and make sure the airflow openings are clear.
• Fill carefully. Open the silicone fill port, angle the bottle nozzle against the side of the opening and let the liquid run down the wall. Do not fill over the central tube, because flooding the airflow channel causes gurgling and leaks. Stop below the maximum line and leave a small air gap at the top.
• Close the fill port. Press the bung in firmly until it is flush with the pod body.
• Prime the coil. Stand the pod upright for five to ten minutes so the cotton can soak up liquid, and give thicker, high-VG liquids the full ten minutes or longer. Skipping this step is the most common cause of a dry hit on the first puff.
• Fit the pod. Push it into the device until it sits fully home, then switch the device on according to its manual.
• Start gently. Take a few short, light draws at the lower end of the recommended wattage range, then raise the power in small steps until the flavour and warmth suit you.

Once it is running, keep the pod topped up before it drops very low. Running a 0.25 ohm coil almost dry is the quickest way to scorch the cotton. Take puffs of two to four seconds with a pause between them rather than long, back-to-back chain draws, so the wick has a chance to re-saturate.

For storage, keep the device upright where possible, away from direct sunlight and heat, and out of reach of children and pets. If you are leaving it unused for a long period, remove the pod to avoid slow leaking onto the contacts. When a pod is spent, empty any remaining liquid and take it to a vape recycling point instead of putting it in your household bin.

Troubleshooting common problems

Most problems with pod systems come down to a handful of causes. This list covers the common ones, roughly in the order you are likely to meet them.

• Leaking from the base or drip tip. Usually overfilling, a fill bung that has not been pressed in fully, or a pod that has been stored on its side. Wipe the pod and the device contacts, refill below the line and make sure the bung is flush. A cracked pod body will leak persistently and should be replaced.
• Gurgling or spitting. Liquid has flooded the airflow channel. Remove the pod, wipe the airflow opening and take a couple of gentle draws away from your mouth. If it keeps happening, you are probably overfilling.
• Dry or burnt taste. The coil has run dry or the cotton has scorched. Check the liquid level, let the pod prime again and lower the wattage. If a burnt taste remains after a fresh fill and a short rest, the coil is finished and the pod needs replacing. Do not keep vaping on a burnt coil.
• No vapour, or an error message such as check atomizer. The contacts may be dirty or the pod may not be seated. Remove the pod, wipe the contacts with a dry cloth and refit it firmly. If the message persists, the pod may be incompatible with your device or the coil may have failed.
• Weak or muted flavour. Common with very thick or very sweet liquids that clog the cotton, or with a coil near the end of its life. Try a thinner liquid, a short rest and a slightly higher wattage within the recommended range.
• Harsh throat hit. Normally too much nicotine for the power level, or too high a wattage. Lower the strength or the power.
• Battery runs flat very quickly. Expected with low-resistance coils on a small battery, as explained in the battery section. A battery that suddenly performs far worse than before may be ageing.
• Hissing or crackling. A sign of excess liquid on the coil or flooding. It usually settles after a few draws, and if it continues, take the pod out and let it dry.

Safety comes first. If a device gets very hot, smells of burning, swells or leaks fluid from the battery area, stop using it, disconnect it from any charger and put it somewhere safe, away from flammable surfaces. Do not attempt to repair a damaged battery. If a pod arrives faulty or damaged, contact us with your order number and clear photos, and we will look into it.

Value for money and how it compares

Judging value on a consumable like this comes down to cost per day of use, not just the price on the page. A pack of two pods gives you two separate coils, and at typical use of one to two weeks per pod for a moderate vaper, a pack covers roughly two to four weeks. Heavy users and sweet-liquid fans will get less out of each pod. Check the current price on this page and divide it by the number of days you expect to get from the pack. That figure is the honest comparison against other options.

Compared with single-use hardware, a refillable pod system is almost always cheaper over time, because you buy e-liquid in bottles and replace the pod, not an entire battery-and-coil assembly. It also produces far less electronic waste, which matters now that single-use vapes are banned from sale in the UK.

How does it compare with alternatives in the same category? Fair comparisons are only possible in broad terms, because pod systems differ in format:

• Standard 0.6 to 1.0 ohm pods: cheaper to run, longer coil life, better battery life and a tighter draw. They suit new switchers better, so choose the 0.25 ohm option only if you want the extra vapour and warmth.
• Other brands' low-resistance pods: several brands, including Vaporesso, OXVA and Smok, make pods commonly in the 0.4 to 0.6 ohm range for looser draws. They are a reasonable middle ground. Pods are not interchangeable between brands, so this only helps if you are choosing a new device rather than feeding an Orion.
• Sub-ohm tanks on larger regulated devices: if you want the most vapour possible, a larger tank on a bigger battery generally costs less per ml of liquid, though at the cost of size and a steeper learning curve.
• Pre-filled closed pods: simpler, with no filling at all, but they usually cost more per ml and cannot be topped up, so they suit light users better than someone who vapes steadily.

The honest summary is that this pod is good value if you already own the device it is built for and you like the experience it creates. It is poor value if the draw or the refill rate does not suit you, or if you are buying it for a device it does not fit. Because it is sold as a two-pack, it is a low-risk way to try the 0.25 ohm resistance. Our advice is to buy one pack, run both pods through your normal routine and then decide whether to stock up. When the pods are finished, drop them at a vape recycling point so the plastic and any residue are handled properly.