Geekvape Boost Pro 2 Vape Kit Silver

Overview

The Geekvape Boost Pro 2 Vape Kit Silver by Geekvape in Silver at 0mg. Free UK delivery over £20, same-day dispatch on weekday orders before 4pm.

Geekvape Boost Pro 2 Vape Kit overview

The Geekvape Boost Pro 2 Vape Kit is a refillable pod-and-coil system from Geekvape, a manufacturer with a long record in pod mods, sub-ohm tanks and tank-style kits. The Boost range has always sat in the middle ground between the small press-and-go pod vapes and the larger box mods. It gives you enough control to tune the power and the draw, but it is still small enough to carry in a jacket pocket and simple enough to refill in under a minute. The Boost Pro 2 follows the same idea. It is built for adult smokers and existing vapers who want a proper refillable device, with their own choice of e-liquid, nicotine strength and coil, rather than a sealed unit that gets thrown away after a few days.

The timing matters for UK buyers. Single-use disposable vapes became illegal to sell in the UK on 1 June 2025, so anyone who used to rely on a 600-puff disposable now needs a rechargeable, refillable alternative. A kit like the Boost Pro 2 is the obvious replacement. The upfront cost is higher than a single disposable, but the running cost is a fraction of it. A 10 ml bottle of e-liquid and an occasional coil change cover several weeks of use for most people, and the device itself lasts for months or years if it is looked after.

This guide covers what the kit actually does day to day: performance, flavour, battery, coils, nicotine choice, setup, troubleshooting and how it compares with other kits at a similar price. We have kept the claims grounded. Where an exact figure such as the wattage ceiling or the battery capacity depends on the variant you pick, we say so and point you to the specification table on the product page rather than guessing.

One note on the variants. The nine listings in this product family are finish and colour options of the same kit, not different flavours, because the Boost Pro 2 ships without e-liquid. The flavour you vape is decided entirely by the bottle you buy. Pick the colour you like and expect the same electronics and the same coil system underneath. If a listing shows a different bundle, such as extra coils or a spare pod, the description on that page will say so.

What is in the box and the key specifications

A Geekvape kit of this type normally arrives with the device, a pod for it, a USB-C charging cable, spare seals or O-rings, and the user manual with a warranty card. Some bundles add a spare coil head. Contents can differ slightly between bundles, so check the box contents line on the product page for the variant you choose. The kit does not include e-liquid, and it does not include nicotine, so you will need to buy a bottle separately. You must be 18 or over to buy it, and we may ask for age confirmation on delivery.

Here is what we can say with confidence about the format, and what to check in the specification table:

• Format: refillable pod kit with replaceable coil heads, not a disposable and not a sealed prefilled system.
• Pod capacity in the UK: 2 ml. UK rules limit the tank or pod on a nicotine vaping product to 2 ml, so UK-edition pods are sized to that limit even where the same device sells abroad with a larger pod.
• E-liquid bottle size: refills for nicotine e-liquid are sold in bottles of up to 10 ml in the UK, which is why you will see 10 ml bottles on every shelf.
• Nicotine ceiling: 20 mg/ml is the maximum strength allowed on e-liquid sold in the UK. It is the same ceiling that applied to the old disposables, and it applies to your refills too.
• Coil system: replaceable Geekvape coil heads, with mesh options available for flavour and vapour production.
• Charging: modern Geekvape devices charge over USB-C, which means the same cable as most current phones and tablets.
• Power: adjustable output within the range printed on the spec table. Always set the wattage inside the window printed on the coil head you have fitted.

We deliberately leave the exact wattage maximum and battery capacity to the spec table on the page. Those two numbers can vary between regional editions and bundles, and a wrong figure in a description is worse than no figure, because it leads people to pick the wrong coil or the wrong charging habit. Treat the spec table and the printed manual as the authority, and treat this guide as the practical explanation of what those numbers mean when you are actually vaping.

Performance and vapour delivery

A refillable kit has no fixed puff count the way a disposable does. The number of puffs you get depends on how much e-liquid you load, what power you vape at, how long each puff lasts and how thick the liquid is. That said, you can estimate it. A 2 ml fill at a restricted, mouth-to-lung setting with a modest wattage typically gives somewhere around 300 to 600 puffs. At higher power with longer, more open draws the same 2 ml disappears faster, often closer to 200 to 300 puffs. Those are rough working figures, not laboratory results, but they give a realistic picture: you refill the pod once or twice across a normal day rather than carrying a dozen disposables.

On the performance side, the Boost line is designed for quick coil warm-up and consistent output. You press the fire button or draw, depending on the mode, and the coil reaches working temperature in a fraction of a second. Output stays steady as long as the battery has charge, because the chip regulates the power rather than letting it sag. The practical effect is that your fourth puff of the day and your four-hundredth puff of the day taste much the same, until the battery gets low or the coil wears out.

What you should expect in use:

• Throat hit: adjustable. Lower wattage with a nicotine salt gives a smooth, cigarette-like hit. Higher wattage with a freebase liquid gives a harsher, warmer one.
• Vapour volume: moderate to good for a pocket-sized kit. It will not match a large sub-ohm tank on a box mod, and it is not meant to.
• Flavour intensity: strongest at the middle of the coil's recommended wattage range. Going to the top of the range often burns the flavour and the liquid faster for little gain.
• Airflow: a tighter draw feels closer to a cigarette. An open draw cools the vapour and gives bigger clouds, but uses more liquid and more battery.

Honest limits are worth stating. If you want huge clouds, a dedicated sub-ohm setup is a better fit. If you want something you can forget about for a day without topping up, a prefilled pod system is simpler. The Boost Pro 2 sits between those, and its strength is balance: a satisfying draw, a refill routine measured in seconds, and enough adjustment to let you find a setting you like and then leave it alone.

Flavour profile and choosing the right e-liquid

The kit has no flavour of its own. What you taste is the e-liquid, filtered through the coil, so the useful question is which liquids suit this kind of device. Mesh and fine-wire coils in a pod-style kit are good at bringing out clear, defined flavours, and they tend to reproduce fruit, menthol and dessert profiles faithfully without muddying them. If you are coming from disposables, you can buy refills that echo your favourites and, usually, get a more even flavour from the first puff to the last because the coil is fresh every time you change it.

These are the profiles that work well, with example e-liquid styles to look for:

• Blue raspberry ice: a sweet-sharp fruit with a cooling finish, one of the most popular flavours for disposables switchers.
• Strawberry kiwi: a balanced, juicy blend that stays clear at middle wattages.
• Mango and peach: rounder, softer fruit that benefits from a slightly warmer setting.
• Cola or energy-drink styles: a fizzy, tangy profile that stays sharp on mesh coils.
• Fresh mint and menthol: clean and cooling, and kind to coils because menthol liquids carry little sweetener.
• Classic tobacco: the natural choice for people stepping across from cigarettes, and best at lower wattage.
• Vanilla custard and bakery styles: rich and creamy, though heavy sweeteners shorten coil life, so expect to change the coil a little more often.
• Lemonade and citrus blends: bright and refreshing, particularly good with a cooling note.

Match the liquid to the coil. Most pod-style coils prefer a 50/50 or 60/40 VG to PG ratio. A 50/50 liquid wicks quickly, tastes sharper and gives a stronger throat hit. A higher VG liquid makes bigger vapour but is thicker, and thick liquids can starve a small coil of fuel, leading to dry hits. If a bottle says it is a max VG liquid designed for sub-ohm tanks, check that it is suitable before putting it in a pod kit.

If you like to swap between flavours, expect a little ghosting: a trace of the previous flavour that lingers in the coil's cotton for a few puffs. The simple fixes are to empty and rinse the pod, let it dry and refill, or to keep a separate coil head for each flavour family. Staying within one family, such as fruit to fruit or menthol to menthol, hardly shows the effect at all. The nine colour finishes of this kit do not change any of this, because the electronics and the coil system are the same.

Design, build quality and ergonomics

Geekvape tends to build its mid-range devices with a metal-alloy chassis, usually zinc alloy, finished in a coating or textured panel, and that is the style you should expect here. The practical advantages are rigidity and a solid in-hand feel. The trade-off is weight: metal-bodied pod mods are heavier than plastic-shelled pod vapes, which you will notice if you are used to a light disposable. Most people stop noticing within a day or two, particularly when the device is carried in a pocket or bag rather than held up.

The shape is a compact handheld that fits a normal adult palm, with the fire button and the controls placed where a thumb or index finger lands naturally. The pod seats into the top of the device and is held in place by a firm clip or magnetic connection, so it does not rattle or twist once seated. The drip tip is a comfortable, rounded shape that suits lips well during longer sessions. Colour and finish are the only differences between the nine variants in this family, and Geekvape's colour range tends to run from understated blacks and greys through to brighter and more decorative finishes.

Points that matter in everyday use:

• Pod seating: push until you feel it settle. A half-seated pod is the cause of many apparent faults, such as a no-coil message or weak vapour.
• Leak protection: pods rely on silicone seals. Check that the seal is flat and seated when you refill, and avoid overfilling above the fill line.
• Button feel: a clear click helps avoid accidental firing in a pocket. If your device offers a lock function, use it when carrying the kit.
• Screen or indicator: shows battery state and output so you know where you are without guessing. Brightness can often be reduced to save charge.
• Surface finish: textured and coated surfaces resist fingerprints better than polished ones, but any coating will wear at the edges over months of pocket use.

Build quality in this class is generally good, and the weak points are the usual ones: seals, coil contacts and ports. Keep the charging port free of lint, keep the pod contacts clean and dry, and the device should look and work well for a long time. Dropping it on a hard floor is the real risk, as with any handheld electronic, so a case or silicone sleeve is a sensible and inexpensive extra if you carry it loose in a bag.

Battery, charging and runtime

The exact battery capacity is shown in the spec table for your variant, and it matters more than any other number when you are working out how long the kit lasts. To help you read it, here is a worked example. A 1,500 mAh cell at a nominal 3.7 V stores about 5.5 watt-hours. A three-second puff at 15 W uses roughly 0.0125 watt-hours, so after allowing for some conversion loss you get in the region of 350 to 400 puffs from a full charge. At 25 W the same cell gives around 220 to 250 puffs. These are illustrative sums, not claims about a particular variant, but they show the pattern: runtime falls quickly as wattage climbs, so running a lower power setting is the most effective way to stretch a charge.

If you vape at moderate power, you should plan on charging the kit once a day, usually overnight or while you are at a desk. If you vape heavily at high wattage, you may need a top-up in the afternoon. Charging over USB-C is quick, and a standard phone charger or a computer port is fine. A good rule is to avoid cheap unbranded chargers, because poor voltage control is harder on cells over time.

Battery and charging habits worth adopting:

• Charge on a hard surface, in view: not under a pillow, not on a sofa, and not unattended for long periods.
• Unplug when full: modern chips stop charging at full, but there is no benefit in leaving a device on the cable for days.
• Avoid extreme heat and cold: a hot car or a freezing pocket shortens battery life and can trigger protection shutdowns.
• Do not carry loose with keys or coins: metal can short external contacts. A pocket with nothing else in it, or a case, avoids the risk.
• Stop using it if it swells, smells or gets unusually hot: a damaged battery is not safe to charge or carry.

When the device or its battery reaches the end of its life, do not put it in a general bin or kerbside recycling. Lithium cells cause fires in bin lorries and recycling plants. Take used vapes and batteries to a retailer that offers take-back, or to a council recycling centre with a small electricals or battery drop-off point. Since single-use vapes were banned, refillable kits like this one have a much longer life, so the volume of waste per vaper falls sharply, and returning the device properly at the end makes that benefit real.

Coil and mesh technology

The coil is where the e-liquid becomes vapour, and it is the single biggest influence on flavour, throat hit and vapour volume. The Boost Pro 2 uses replaceable Geekvape coil heads that fit into the pod. Each head contains a resistance wire, usually in a mesh or a fine-wire form, wrapped or backed by organic cotton that wicks e-liquid towards the heating element. When you fire the device, the coil heats the liquid in the cotton, and the airflow carries the vapour to your mouth.

Mesh coils use a flat or curved sheet of metal with a pattern of openings, instead of a round wire in a spiral. The larger heating area warms evenly, which tends to give smoother flavour and less hot-spotting, and it usually reaches working temperature quickly. Round-wire coils are simpler and heat more directly, and they can be good for a firmer throat hit and efficient battery use. Both types work well when matched to the right liquid and power setting.

Resistance, measured in ohms, is the other half of the picture. As a general guide:

• Higher resistance, around 0.8 to 1.2 ohm: lower wattage, tighter draw, stronger throat hit, longer battery life. Best with nicotine salts and 10 to 20 mg/ml strengths.
• Middle resistance, around 0.4 to 0.7 ohm: a balanced setting with more vapour and warmer flavour, suitable for 6 to 12 mg/ml liquids.
• Lower resistance, below about 0.4 ohm: high-power, bigger-cloud territory, suited to lower nicotine strengths and thinner airflow restrictions removed.

Every Geekvape coil prints a recommended wattage range on its packaging and often on the coil itself. Stay inside that window. Going over it burns the cotton, tastes harsh and shortens coil life. Going well under gives a cool, thin vape. Start at the bottom third of the range and move up in small steps until the flavour and warmth feel right.

Coil life depends on liquid and habit. A typical coil lasts one to three weeks of regular use. Sweet, heavily flavoured and dessert liquids leave residue on the cotton and mesh, so they shorten life, while menthol and lighter fruit liquids are easier on the coil. Signs it is time to change: a burnt or muted taste even with fresh liquid, gurgling or leaking that was not there before, and a noticeably weaker hit. Always prime a new coil before use: add a few drops of e-liquid directly onto the cotton, fill the pod, then wait five to ten minutes before the first puff. Skipping that wait is the main cause of burnt new coils.

Nicotine strength guidance

Choosing a nicotine strength is a matter of matching your current habit to the device's power. UK law caps nicotine e-liquid at 20 mg/ml, which is the figure you see on the highest-strength bottles. That means you do not have to guess whether a strong liquid is legal, because every bottle from a UK retailer sits at or below it. What you do have to decide is where within that range you should sit, and the answer depends on how much you smoked or vaped before and how you plan to use the kit.

As a practical starting guide, based on common experience and not on medical advice:

• Heavy smokers, around 15 or more cigarettes a day: start with a 20 mg/ml nicotine salt at a low, restricted setting. This delivers a satisfying hit without needing a lot of vapour.
• Moderate smokers or frequent vapers: 10 to 12 mg/ml nicotine salt is often enough and feels smoother.
• Lighter or social smokers, or those cutting down: 5 to 6 mg/ml, or a lower strength, keeps the experience gentle.
• Higher wattage and more open airflow: choose a lower strength. You are inhaling much more vapour per puff, so you take in more nicotine per puff even if the strength on the bottle is modest.

Nicotine salts and freebase nicotine behave differently. Salts are smoother at high strengths, which is why 10 to 20 mg/ml salts are popular in pod kits. Freebase nicotine is harsher at the same strength, so it is usually used at 3 to 6 mg/ml with more open, higher-power setups. If you find a liquid too harsh, check which type it is before changing the strength.

If the strength is too low, you will notice yourself chain-vaping, feeling unsatisfied after a session, or craving a cigarette sooner. If it is too high, you may feel light-headed, nauseous or jittery, and your throat will feel scratchy. In that case, stop and move down a strength. Many people find their ideal strength drops over weeks as they settle into the habit, and stepping down gradually is easier than jumping. Nicotine is addictive, vaping is not risk free, and these products are for adults who smoke or already vape. They are not for non-smokers, people under 18, or anyone pregnant or with a heart condition, who should talk to a doctor or pharmacist first.

Who the Boost Pro 2 is for, and who should skip it

No kit suits everyone, and a good purchase starts with an honest match. The Boost Pro 2 is a mid-sized, adjustable pod kit, and it fits some people very well and others poorly.

It is a good fit if you are:

• A smoker switching away from cigarettes and want a device that can be set to a tight, cigarette-style draw with a nicotine salt.
• A disposable vaper who wants to stop buying disposables and prefers a refillable setup with lower running costs, your own choice of flavours and replaceable coils.
• An existing vaper who wants a second device that is more portable than a tank-and-mod setup but still adjustable.
• Someone who values control and wants to adjust power and airflow rather than accept a single fixed setting.
• A user who prefers a metal body and a solid feel over a very light plastic shell.

You might want to skip it, or look at an alternative, if you are:

• A complete beginner who wants zero setup. A simpler auto-draw pod kit with no buttons or settings is quicker to learn. The Boost Pro 2 is not hard, but it does ask you to pick a wattage, prime a coil and fill a pod.
• A cloud chaser. Large sub-ohm tanks on a dedicated mod produce far more vapour than any 2 ml pod system can.
• Someone who dislikes any maintenance. Coils need replacing, pods need cleaning and seals need checking from time to time.
• A non-smoker or someone under 18. Nicotine vaping products are not intended for you and are illegal to sell to under-18s in the UK.
• Someone who needs the lightest possible device to carry all day, in which case a slim plastic pod kit weighs less.

A final practical point: if you share a household with children or pets, keep e-liquid in its original childproof bottle, store the kit and any spare pods out of reach, and never leave filled pods lying around. Nicotine liquid is poisonous if swallowed or absorbed through skin in quantity, and the sweet flavours that appeal to adults can also appeal to children.

How to set up and use the kit

Setting up takes about ten minutes, most of which is waiting for the coil to soak. Follow the steps in order and the first session will be a good one.

• Step 1, charge it: plug in the USB-C cable and charge the device fully before the first use, which sets a sensible baseline for the battery.
• Step 2, prepare the pod: take the pod out of its packaging and, if a protective film or plug is fitted, remove it. Check the coil head is fitted and fully clicked in.
• Step 3, prime the coil: add two or three drops of e-liquid directly onto the cotton through the coil opening. This wets the cotton before power is applied.
• Step 4, fill the pod: open the fill port, which the manual shows, and fill slowly with the bottle tip angled against the side wall so air can escape. Stop at or just below the fill line. Close the port firmly.
• Step 5, wait: leave the filled pod standing upright for five to ten minutes. The cotton needs time to soak right through.
• Step 6, fit the pod: push it into the device until it seats.
• Step 7, power on: most Geekvape devices switch on and off with several quick presses of the fire button, commonly five, but check the manual for your variant. Set a wattage in the bottom third of the coil's printed range.
• Step 8, take the first puffs: draw slowly with the airflow on a tighter setting. Increase power by one or two watts at a time if the vapour feels thin.

For daily use, top up the pod when it drops to about a quarter full rather than letting it run dry. Running dry is how dry hits and burnt coils happen. When you are done, use the lock function if your device has one, and keep the kit upright in a bag or pocket to limit leaks.

For cleaning, wipe the mouthpiece with a dry cloth, clean the pod contacts with a dry cotton bud and never use water on the electronics. Rinse a pod only if you are changing flavour, and let it dry fully first. When you change a coil, remove the pod, pull the old head out, fit the new one, prime it, and wait before you vape. Following that same routine every time gives you consistent flavour and longer coil life.

Troubleshooting common problems

Most problems with a pod kit have simple causes. Work through the likely ones before you assume the device is faulty.

• Leaking from the pod or into the device: usually overfilling, a seal not seated flat, or a loose coil head. Empty the pod, check the seals, refit the coil firmly and refill below the fill line. Store the kit upright and avoid pressure changes such as a hot dashboard or an aircraft hold.
• Burnt or harsh taste: the wick is dry or the coil is worn. Check the e-liquid level, prime a new coil properly and wait before vaping, or lower the wattage. If the taste stays burnt with fresh liquid and a fresh coil, the wattage is likely too high.
• Weak flavour or thin vapour: coil wear is the common cause. Change the coil. If the coil is new, try a slightly higher wattage within the printed range, or check that the liquid is not too thick for the coil.
• No vapour or a no-coil or short-circuit message: remove the pod, wipe the contacts with a dry cotton bud and reseat it. Check that the coil head is fully pushed in.
• Gurgling or spitting: too much condensation or flooded airflow. Blow gently through the mouthpiece to clear it, wipe the tip and reduce the amount of e-liquid in the pod.
• Device will not charge: try a different cable and a different power source, then clear any lint from the port with a wooden toothpick. If it still does not charge, contact us with your order number.
• Battery drains fast: check the wattage, because higher power drains cells quickly. If the battery has aged a lot, capacity will drop, and this is normal after many months of daily use.
• Device gets warm: mild warmth during use is normal. If it becomes hot to hold, stop, unplug it, let it cool and contact support if it repeats.
• Accidental firing: use the lock function and carry the kit in a clean pocket or a case.

If none of these resolve the issue, take a photo or a short video of the fault, note the order number and the variant, and contact the shop. Faults found early are easier to resolve, and photos speed up the process. Your statutory consumer rights apply to faulty goods bought in the UK, and the manufacturer's own warranty card in the box provides additional cover, subject to its terms. Wear and tear items such as coils and seals are consumables and are normally outside warranty.

Value for money and how it compares

Value for a refillable kit is mostly about the running cost, not the sticker price. A typical heavy disposable user in the UK used to spend several pounds a week on single-use devices. A refillable kit shifts that spend to a 10 ml bottle of e-liquid, which usually costs a few pounds and lasts a week or more, plus a coil every couple of weeks, which is also a few pounds. Over a month the maths often favours the refillable kit even after you count the purchase price, and over a year it is clearly cheaper. You also get the benefit of choosing from hundreds of liquids rather than whatever flavours a disposable brand releases.

Comparisons are worth making honestly. The kit sits among several well-known families, and the right choice depends on what you value:

• Vaporesso XROS series: usually slimmer and lighter, with simpler controls and a strong reputation for ease of use. It is a good pick if you want minimum fuss. The Boost Pro 2 is generally the better pick if you want more adjustment and a heavier, more robust body.
• Uwell Caliburn series: compact, popular with mouth-to-lung vapers and simple to run. If you prefer a very small, fixed-output device, a Caliburn can be easier. If you want to change power, the Boost Pro 2 gives more room to move.
• Voopoo Vinci and Drag families: broader power ranges and chip features, often at a higher price. They suit more experienced vapers who like to tinker. For most adults moving off cigarettes or disposables, the extra range is not necessary.
• SMOK Nord series: long-established and flexible with a wide coil range. Choose it if coil variety matters most to you.

Competitor specifications change between generations, so use this as a general guide and check the current spec of any alternative before you buy. The Boost Pro 2 earns its place on balance: a solid build, adjustable power, replaceable coils and a refill routine that is quick to learn.

For UK buyers, two practical points round out the value picture. First, buying from a UK shop means the products are labelled, notified and sold under the UK rules on nicotine strength, bottle size and tank size, with age checks at purchase. Second, plan the end of life from the start: used vapes and batteries should go to a retailer take-back scheme or a council recycling point, never into household bins. Following those two rules, the Boost Pro 2 is a sensible, long-lasting replacement for disposables, and you can browse the other colours in this family to pick the finish you like best.